[Previous][Next]
DTC No. P1AA0-1C: DCDC input over voltage
 
 
danger
 
 
 
 
TROUBLE JUDGMENT
Check Condition
  • The power supply mode of the electric motor switch is ON (READY indicator: ON) or during charging.
Judgment Criterion
  • The input voltage malfunction of the high voltage system is detected.
 
 
TROUBLESHOOTING HINTS
  • Malfunction of the high-voltage circuit
  • Malfunction of the junction box
  • Malfunction of the high-voltage fuse (30 A) for On Board Charger (OBC)/DC-DC converter
  • Malfunction of the On Board Charger (OBC)/DC-DC converter
 
 
DIAGNOSIS
Required Special Tools:
  • MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
  • MB992745: V.C.I.-Lite main harness A
  • MB992747: V.C.I.-Lite USB cable short
  • MB992748: V.C.I.-Lite USB cable long
  • MB991223: Wiring harness set
  • MB992006: Extra fine probe
1.M.U.T.-IIISE other system DTC
Check whether the REMCU sets the following DTC.
  • Code No. P30D1-16 Rear drive motor voltage-low
  • Code No. P0C7A-00 Rear drive motor voltage-high
Is the DTC set?
Troubleshoot the set DTCs (Refer to DTC No. P0C7A-00 Rear drive motor voltage-high) .
 
2.Check of the high-voltage fuse (30 A) for On Board Charger (OBC)/DC-DC converter
danger
  • Carry out the check on the high-voltage circuit while reading carefully the precautions on handling a high-voltage vehicle.
  • Wear the specified protection equipment during the check.
Check the high voltage fuse (30 A) for On Board Charger (OBC)/DC-DC converter (Refer to CHECK AND REPLACEMENT OF HIGH-VOLTAGE FUSE INSIDE THE JUNCTION BOX).
Is the check result normal?
Replace the high voltage fuse (30 A) for On Board Charger (OBC)/DC-DC converter.
 
3.Visually check of the inside of the junction box
danger
  • Carry out the check on the high-voltage circuit while reading carefully the precautions on handling a high-voltage vehicle.
  • Wear the specified protection equipment during the check.
Visually check that there is no burnout, damage, foreign material inside the junction box.
Is the check result normal?
Replace the junction box (Refer to JUNCTION BOX REMOVAL AND INSTALLATION).
 
4.Check the installation of the P, N terminals on On Board Charger (OBC)/DC-DC converter.
danger
  • Carry out the check on the high-voltage circuit while reading carefully the precautions on handling a high-voltage vehicle.
  • Wear the specified protection equipment during the check.
Check that the P, N terminals of the On Board Charger (OBC)/DC-DC converter is installed to the junction box with specified torque.
Is the check result normal?
Repair the installation.
 
5.Check of continuity at the high-voltage circuit inside the junction box.
danger
  • Carry out the check on the high-voltage circuit while reading carefully the precautions on handling a high-voltage vehicle.
  • Wear the specified protection equipment during the check.
Check the continuity of the high-voltage circuit inside the junction box (Refer to CONTINUITY CHECK FOR HIGH VOLTAGE CIRCUIT IN JUNCTION BOX).
Is the check result normal?
Check the tightening torque of the fuse, or repalce the junction box.
 
6.Check whether the DTC is set again.
(1) Erase the set DTC.
(2) Change the power supply mode of the electric motor switch to ON (READY indicator: ON).
(3) Check whether the DTC is set again.
Is the DTC set?
Repalce the On Board Charger (OBC)/DC-DC converter (Refer to ON BOARD CHARGER (OBC) &DC-DC CONVERTER REMOVAL AND INSTALLATION).
The trouble can be an intermittent malfunction (Refer to General Information - How to Use Troubleshooting/Inspection Service Points, How to Cope with Intermittent Malfunctions HOW TO COPE WITH INTERMITTENT MALFUNCTIONS).