[Previous][Next]
DTC P2419-00: EVAP System Switching Valve Control Circuit Low
 
 
 
 
CIRCUIT OPERATION
  • The 12V battery voltage is applied to the fuel tank solenoid valve connector terminal number 1 from the ECM connector terminal number 92.
  • The fuel tank solenoid valve connector terminal number 2 is grounded with the vehicle body.
 
 
TECHNICAL DESCRIPTION
Seal the fuel tank and keep the fuel tank internal pressure. In response to a signal from the ECM, open the fuel tank solenoid valve and release the sealed state of the fuel tank.
 
 
MONITOR EXECUTION
Continuous
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC set in memory for the item monitored below)
  • Not applicable
Sensor (The sensor below is determined to be normal)
  • Not applicable
 
 
DTC SET CONDITIONS
Logic Flow Chart
Check Conditions
  • Power supply mode of electric motor switch is ON.
  • 12V battery positive voltage is between 10.0 and 16.5 volts.
Judgment Criterion
  • Monitor circuit voltage is 0.4 volt or lower for 2 seconds.
 
 
FAIL-SAFE AND BACKUP FUNCTION
  • Fuel filler lid cannot be opened even when pressing the fuel filler lid opener switch.
  • Indicates "REFUELING SYSTEM SERVICE REQUIRED" on the information screen in the multi-information display.
 
 
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function, OBD-II Drive Cycle – Pattern 1 OBD- II DRIVE CYCLE.
 
 
TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
  • Fuel tank solenoid valve failed.
  • Shorted fuel tank solenoid valve circuit or connector damage.
  • ECM failed.
 
 
DIAGNOSIS
Required Special Tools:
  • MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
  • MB992745: V.C.I.-Lite main harness A
  • MB992747: V.C.I.-Lite USB cable short
  • MB992748: V.C.I.-Lite USB cable long
1.STEP 1. Using scan tool (M.U.T.-IIISE), perform the actuator test.
Use scan tool (M.U.T.-III SE) to perform the actuator test (Refer to ACTUATOR TEST REFERENCE TABLE).
  • Item number 100: EVAP system sealing valve
OK: Select ON to drive the solenoid valve.
Q: Is the check result normal?
 
2.STEP 2. Check the fuel tank solenoid valve.
Check coil resistance of fuel tank solenoid valve (Refer to ENGINE, Engine, Motor and Emission Control – Emission Control – Evaporative Emission System FUEL TANK SOLENOID VALVE CHECK).
OK: 25 to 30 ohms [at 20°C (68°F)]
Q: Is the check result normal?
Replace fuel tank solenoid valve (Refer to ENGINE, Fuel Supply – Fuel Tank FUEL TANK DISASSEMBLY AND ASSEMBLY)
 
3.STEP 3. Check harness between fuel tank solenoid valve connector terminal number 1 and ECM connector terminal number 92.
Check power supply line for short to ground.
Q: Is the check result normal?
Repair or replace the connector, or repair the damaged harness wire.
 
4.STEP 4. Using scan tool (M.U.T.-IIISE), perform the actuator test.
Use scan tool (M.U.T.-III SE) to perform the actuator test (Refer to ACTUATOR TEST REFERENCE TABLE).
  • Item number 100: EVAP system sealing valve
OK: Select ON to drive the solenoid valve.
Q: Is the check result normal?
Replace the ECM (Refer to ENGINE CONTROL MODULE (ECM) REMOVAL AND INSTALLATION).
 
5.STEP 5. Test the OBD-II drive cycle.
After erasing the DTC, carry out test drive with the drive cycle pattern, and recheck the DTC.
(1) Use scan tool (M.U.T.-III SE) to erase the DTC.
(2) Carry out test drive with the drive cycle pattern (Refer to Diagnostic Function, OBD-II Drive Cycle – Pattern 1 OBD- II DRIVE CYCLE).
(3) Use scan tool (M.U.T.-III SE) to recheck the DTC.
Q: Is DTC P2419-00 set?
Replace the ECM (Refer to ENGINE CONTROL MODULE (ECM) REMOVAL AND INSTALLATION).
Intermittent malfunction (Refer to GENERAL INFORMATION, General Information – How to Use Troubleshooting/Inspection Service Points – How to Cope with Intermittent Malfunctions HOW TO COPE WITH INTERMITTENT MALFUNCTIONS).