[Previous][Next]
DTC P0458-00: Purge control solenoid valve circuit low input
 
 
 
 
CIRCUIT OPERATION
  • MFI relay is built into the IPDM E/R.
  • Power is supplied to the evaporative emission purge solenoid connector terminal number 2 from the MFI relay connector terminal.
  • The ECM connector terminal number 14 makes the power transistor in the unit be in ON position, and that makes currents go on the evaporative emission purge solenoid connector terminal number 1.
 
 
TECHNICAL DESCRIPTION
In response to a signal from the ECM, the evaporative emission purge solenoid controls the flow rate of the purge air to be introduced into the intake manifold.
 
 
DESCRIPTIONS OF MONITOR METHODS
The ECM detects open circuit and short malfunction.
 
 
MONITOR EXECUTION
Continuous.
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC set in memory for the item monitored below)
  • Not applicable
Sensor (The sensor below is determined to be normal)
  • Not applicable
 
 
DTC SET CONDITIONS
Logic Flow Chart
Check Conditions
  • More than 2 seconds have passed since the power supply mode of the electric motor switch was ON.
  • Evaporative emission purge solenoid is OFF.
  • 12V battery positive voltage is between 10.0 and 16.5 volts.
    or
  • More than 2 seconds have passed since the key-off evaporative leakage monitoring was started.
  • Evaporative emission purge solenoid is OFF.
  • 12V battery positive voltage is between 10.0 and 16.5 volts.
Judgment Criterion
  • The supply voltage is 3 volts or lower without the evaporative emission purge solenoid driving for 2 seconds.
 
 
FAIL-SAFE AND BACKUP FUNCTION
Prohibit introduction of purges.
 
 
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function, OBD-II Drive Cycle – Pattern 1 OBD- II DRIVE CYCLE.
 
 
TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
  • Evaporative emission purge solenoid failed.
  • Open or shorted evaporative emission purge solenoid circuit, harness damage or connector damage.
  • ECM failed.
 
 
DIAGNOSIS
Required Special Tools:
  • MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
  • MB992745: V.C.I.-Lite main harness A
  • MB992747: V.C.I.-Lite USB cable short
  • MB992748: V.C.I.-Lite USB cable long
1.STEP 1. Using scan tool (M.U.T.-IIISE), perform the actuator test.
Use scan tool (M.U.T.-III SE) to perform the actuator test (Refer to ACTUATOR TEST REFERENCE TABLE).
  • Item number 30: Purge Control Solenoid Valve
OK: Operating sound can be heard and the valve vibrates
Q: Is the check result normal?
 
2.STEP 2. Check evaporative emission purge solenoid itself.
Check evaporative emission purge solenoid itself (Refer to ENGINE, Engine, Motor and Emission Control – Emission Control – Evaporative Emission System EVAPORATIVE EMISSION PURGE SOLENOID CHECK).
Q: Is the check result normal?
Replace the evaporative emission purge solenoid (Refer to ENGINE, Intake and Exhaust – Intake Manifold INTAKE MANIFOLD REMOVAL AND INSTALLATION).
 
3.STEP 3. Perform voltage measurement at evaporative emission purge solenoid connector terminal number 2.
  • Disconnect connector, and measure at harness side.
  • Power supply mode of electric motor switch: ON
  • Voltage between evaporative emission purge solenoid connector terminal number 2 and ground.
OK: 12V battery positive voltage
Q: Is the check result normal?
Repair or replace the connector, or check and repair harness between IPDM E/R connector terminal number 66 and evaporative emission purge solenoid connector terminal number 2.
 
4.STEP 4. Perform voltage measurement at ECM connector terminal number 14.
  • Disconnect connector, and measure at harness side.
  • Power supply mode of electric motor switch: ON
  • Voltage between ECM connectors terminal number 14 and ground.
OK: 12V battery positive voltage
Q: Is the check result normal?
Repair or replace the connector, or check and repair harness between ECM connector terminal number 14 and evaporative emission purge solenoid connector terminal number 1.
 
5.STEP 5. Check harness between evaporative emission purge solenoid connector terminal number 1 and ECM connector terminal number 14.
Check output line for damage.
Q: Is the check result normal?
Repair or replace the connector, or repair the damaged harness wire.
 
6.STEP 6. Check harness between IPDM E/R connector terminal number 66 and evaporative emission purge solenoid connector terminal number 2.
Check power supply line for damage.
Q: Is the check result normal?
Repair or replace the connector, or repair the damaged harness wire.
 
7.STEP 7. Using scan tool (M.U.T.-IIISE), perform the actuator test.
Use scan tool (M.U.T.-III SE) to perform the actuator test (Refer to ACTUATOR TEST REFERENCE TABLE).
  • Item number 30: Purge Control Solenoid Valve
OK: Operating sound can be heard and the valve vibrates
Q: Is the check result normal?
Replace the ECM (Refer to ENGINE CONTROL MODULE (ECM) REMOVAL AND INSTALLATION).
 
8.STEP 8. Test the OBD-II drive cycle.
After erasing the DTC, carry out test drive with the drive cycle pattern, and recheck the DTC.
(1) Use scan tool (M.U.T.-III SE) to erase the DTC.
(2) Carry out test drive with the drive cycle pattern (Refer to Diagnostic Function, OBD-II Drive Cycle – Pattern 1 OBD- II DRIVE CYCLE).
(3) Use scan tool (M.U.T.-III SE) to recheck the DTC.
Q: Is DTC P0458-00 set?
Replace the ECM (Refer to ENGINE CONTROL MODULE (ECM) REMOVAL AND INSTALLATION).
Intermittent malfunction (Refer to GENERAL INFORMATION, General Information – How to Use Troubleshooting/Inspection Service Points – How to Cope with Intermittent Malfunctions HOW TO COPE WITH INTERMITTENT MALFUNCTIONS).