[Previous][Next]
Inspection procedure 5: Starts up and dies
 
 
 
 
COMMENT
  • In such cases as the above, the cause is usually improper air/fuel mixture. It is possible, though less likely, that the spark plugs are generating sparks but the sparks are weak.
 
 
TROUBLESHOOTING HINTS (The most likely causes for this case:)
  • Fuel pump system failed.
  • Ignition system failed.
  • Injector system failed.
  • Poor compression.
  • EGR system failed.
  • Contaminated fuel.
  • Dirtiness around throttle valve.
  • ECM failed.

 
 
DIAGNOSIS
Required Special Tools:
  • MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
  • MB992745: V.C.I.-Lite main harness A
  • MB992747: V.C.I.-Lite USB cable short
  • MB992748: V.C.I.-Lite USB cable long
  • MB991958: Scan Tool (M.U.T.-III Sub Assembly)
    • MB991824: Vehicles Communication Interface (V.C.I.)
    • MB991827: M.U.T.-III USB Cable
    • MB991910: M.U.T.-III Main Harness A (Vehicles with CAN communication system)
STEP 1. Check if the EGR valve sounds during initialization.
Is the initialization sound heard in the EGR valve?
Go to Step 2.
Refer to GROUP 17, Emission Control - Exhaust Gas Recirculation (EGR) System - EGR Valve (Stepper Motor) Check .
 
STEP 2. Using scan tool (M.U.T.-III), read the diagnostic trouble code (DTC).
cautionTo prevent damage to scan tool (M.U.T.-III), always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool (M.U.T.-III).
(1) Connect scan tool (M.U.T-III). Refer to HOW TO CONNECT THE SCAN TOOL (M.U.T.-III) .
(2) Turn the ignition switch to the "ON" position.
(3) Read the DTC.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is any DTC set?
Refer to Diagnostic Trouble Code Chart .
Go to Step 3.
 
STEP 3. Using scan tool (M.U.T.-III), check data list.
(1) Turn the ignition switch to the "ON" position.
(2) Check the following items in the data list. Refer to Data List Reference Table .
  1. Item 1: Power Supply Voltage
  2. Item 6: Engine Coolant Temperature Sensor
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Is the sensor operating properly?
Go to Step 4.
Repair or replace it. Then confirm that the malfunction symptom is eliminated.
 
STEP 4. Using scan tool (M.U.T.-III), check actuator test.
(1) Turn the ignition switch to the "ON" position.
(2) Check the following item in the actuator test. Refer to Actuator Test Reference Table .
  1. Item 9: Fuel Pump
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Is the actuator operating properly?
Go to Step 5.
Repair or replace it. Then confirm that the malfunction symptom is eliminated.
 
STEP 5. Inspection of throttle body (throttle valve area) for dirtiness.
Is the throttle valve area dirty?
Refer to Throttle Body (throttle valve area) Cleaning .
Go to Step 6.
 
STEP 6. Check the ignition timing.
Refer to GROUP 11C, On-vehicle Service - Ignition Timing Check .
Is the ignition timing normal?
Go to Step 7.
Check for installed conditions of the timing chain. Then confirm that the malfunction symptom is eliminated.
 
STEP 7. Check the injector.
Refer to Injector check .
Is the measured resistance normal?
Go to Step 8.
Replace the faulty injector. Then confirm that the malfunction symptom is eliminated.
 
STEP 8. Check of harness damage in power supply line between MFI relay connector and injector connector.
Are the harness wires in good condition?
Go to Step 9.
Repair the connector(s) or wiring harness. Then confirm that the malfunction symptom is eliminated.
 
STEP 9. Check the spark plugs.
Refer to GROUP 16, Ignition System - On-vehicle Service - Spark Plug Check and Cleaning .
Are there any abnormalities?
Replace the spark plug. Then confirm that the malfunction symptom is eliminated.
Go to Step 10.
 
STEP 10. Check the ignition coil.
Refer to GROUP 16, Ignition System - On-vehicle Service - Ignition Coil Check .
Are there any abnormalities?
Replace the ignition coil. Then confirm that the malfunction symptom is eliminated.
Go to Step 11.
 
STEP 11. Check the compression pressure.
Refer to GROUP 11C, On-vehicle Service - Compression Pressure Check .
Is the compression pressure normal?
  • Check the following items, and repair or replace the defective items.
    1. Check fuel lines for clogging.
    2. Check if fuel is contaminated.
    3. Check if the injectors are clogged.
  • Then confirm that the malfunction symptom is eliminated.
Repair it. Then confirm that the malfunction symptom is eliminated.