DTC U0155-00: Lost Communication with Cluster

caution

If DTC U0155-00 is set in the ECM, surely perform CAN bus line diagnosis.
Replace ECU after certainly confirming that the communication circuits are normal.

DESCRIPTIONS OF MONITOR METHODS

There is no data from combination meter for the specified time (combination meter also detect communication error with ECM).

MONITOR EXECUTION

Continuous.

MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)

Other Monitor (There is no temporary DTC set in memory for the item monitored below)

Not applicable

Sensor (The sensor below is determined to be normal)

Not applicable

DTC SET CONDITIONS

Logic Flow Chart

Check Conditions

Power supply mode of electric motor switch is ON.
12V battery positive voltage is more than10.0 volts and is less than 16.5 volts.

Judgment Criterion

Unable to receive combination meter signals through the CAN bus line for 4 seconds.

COMMENT

Current Trouble

Some of the possible causes are a harness or connector damage between the ECM and the combination meter on the CAN bus line, a failure in the combination meter power supply system, a failure in the combination meter, or a failure in the ECM.

Past Trouble

Proceed to troubleshoot based on a harness or connector damage on the CAN bus line between the ECM and combination meter, and a failure in the combination meter power supply system. For diagnostic procedure, refer to how to cope with past malfunctions (Refer to GENERAL INFORMATION, General Information – How to Use Troubleshooting/Inspection Service Points – How to Treat Past Trouble HOW TO TREAT PAST TROUBLE).

note

If a malfunction occurred in the past, a failure cannot be discovered through the scan tool (M.U.T.-III SE) CAN bus diagnosis even if there might be a problem with the CAN bus. In this case, refer to GENERAL INFORMATION, General Information – How to Use Troubleshooting/Inspection Service Points – How to Cope with Intermittent Malfunctions HOW TO COPE WITH INTERMITTENT MALFUNCTIONS

). Furthermore, it is possible to narrow down the areas of the possible failures from the DTCs that are set in the ECUs, which are communicating on the CAN bus (Refer to ELECTRICAL & POWER CONTROL, LAN System – CAN Fundamental – Basic Inspection – Diagnosis and Repair Workflow – Trouble Diagnosis Flow Chart Trouble Diagnosis Flow Chart

FAIL-SAFE AND BACKUP FUNCTION

None.

OBD-II DRIVE CYCLE PATTERN

Refer to Diagnostic Function, OBD-II Drive Cycle – Pattern 1 OBD- II DRIVE CYCLE

TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)

CAN line harness damage or connector damage.
Combination meter failed.
ECM failed.

DIAGNOSIS

Required Special Tools:

MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
MB992745: V.C.I.-Lite main harness A
MB992747: V.C.I.-Lite USB cable short
MB992748: V.C.I.-Lite USB cable long

1.STEP 1. Using scan tool (M.U.T.-IIISE), diagnostic CAN bus line.

Use scan tool (M.U.T.-III SE) to perform CAN bus line diagnostic (Refer to ELECTRICAL & POWER CONTROL, LAN System – CAN Fundamental – Basic Inspection – Diagnosis and Repair Workflow – Trouble Diagnosis Flow Chart Trouble Diagnosis Flow Chart

Q: Is the CAN bus line normal?

Repair CAN bus line (Refer to ELECTRICAL & POWER CONTROL, LAN System – CAN – DTC/Circuit Diagnosis – Malfunction Area Chart – Drivetrain CAN Communication Circuit Drivetrain CAN Communication Circuit

). Then

2.STEP 2. Using scan tool (M.U.T.-III SE), read the other system DTC.

Use scan tool (M.U.T.-III SE) to check and see if a DTC is set in the combination meter.

Q: Is any DTC set in the combination meter?

Perform troubleshooting of combination meter (Refer to ELECTRICAL AND POWER CONTROL, Body Control System – ECU Diagnosis Information – BCM – DTC Index DTC Index

3.STEP 3. Using scan tool (M.U.T.-III SE), read the other system DTC.

Use scan tool (M.U.T.-III SE) to check and see if a DTC of METER CAN timeout is set in the PHEV-ECU [Refer to ELECTRIC POWER TRAIN, PHEV-ECU – Troubleshooting – Diagnosis Function DIAGNOSTIC FUNCTION

, and check whether the DTC of CAN communication system (Combination meter) is set in the BCM.

Q: Is the DTC of METER CAN timeout set in the PHEV-ECU? Or Is the DTC of CAN communication system (Combination meter) set in the BCM?

4.STEP 4. Test the OBD-II drive cycle.

After erasing the DTC, carry out test drive with the drive cycle pattern, and recheck the DTC.

(1) Use scan tool (M.U.T.-III SE) to erase the DTC.

(2) Carry out test drive with the drive cycle pattern (Refer to Diagnostic Function, OBD-II Drive Cycle – Pattern 1 OBD- II DRIVE CYCLE

(3) Use scan tool (M.U.T.-III SE) to recheck the DTC.

Q: Is DTC U0155-00 set?

Replace the combination meter (Refer to DRIVER INFORMATION & MULTIMEDIA, Meter, Warning & Indicator – Removal and Installation – Combination Meter Removal and Installation

). Then

Intermittent malfunction in CAN bus line between ECM and combination meter (Refer to GENERAL INFORMATION, General Information – How to Use Troubleshooting/Inspection Service Points – How to Cope with Intermittent Malfunctions HOW TO COPE WITH INTERMITTENT MALFUNCTIONS

5.STEP 5. Test the OBD-II drive cycle.

After erasing the DTC, carry out test drive with the drive cycle pattern, and recheck the DTC.

(1) Use scan tool (M.U.T.-III SE) to erase the DTC.

(2) Carry out test drive with the drive cycle pattern (Refer to Diagnostic Function, OBD-II Drive Cycle – Pattern 1 OBD- II DRIVE CYCLE

(3) Use scan tool (M.U.T.-III SE) to recheck the DTC.

Q: Is DTC U0155-00 set?

Replace the ECM (Refer to ENGINE CONTROL MODULE (ECM) REMOVAL AND INSTALLATION

). Then

6.STEP 6. Test the OBD-II drive cycle.

After erasing the DTC, carry out test drive with the drive cycle pattern, and recheck the DTC.

(1) Use scan tool (M.U.T.-III SE) to erase the DTC.

(2) Carry out test drive with the drive cycle pattern (Refer to Diagnostic Function, OBD-II Drive Cycle – Pattern 1 OBD- II DRIVE CYCLE

(3) Use scan tool (M.U.T.-III SE) to recheck the DTC.

Q: Is DTC U0155-00 set?

Retry the troubleshooting

The inspection is complete.