[Previous][Next]
DTC No. P0C30: Battery pack state of charge high
cautionWhenever ECU is replaced, ensure that the CAN bus lines are normal.
 
 
 
 
MONITOR EXECUTION
  • Continuous
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC set in memory for the item monitored below)
  • Not applicable
Sensor (The sensor below is determined to be normal)
  • Not applicable
 
 
DTC SET CONDITIONS
Logic Flow Chart
Check Conditions
  • battery management unit (BMU) power supply voltage is 8 volts to 16 volts.
  • Time after above conditions satisfy is more than 2 second.
Judgment Criterion
  • SOC is more than 120 percent continues for 5 seconds.
 
 
FAIL-SAFE AND BACKUP FUNCTION
  • Not available
 
 
PROBABLE CAUSES
  • Deviation of learning capacity of main drive lithium-ion battery.
  • The battery management unit (BMU) is failed.
 
 
 
 
DIAGNOSIS
STEP 1. Using scan tool (M.U.T.-IIISE), check whether the DTC is set.
Check whether the DTC related to the cell voltage is set in the BMU.
Is the DTC set?
Perform the troubleshooting of DTC (Refer to ).
Go to Step 2.
 
STEP 2. Using scan tool (M.U.T.-IIISE), check whether the DTC is set again.
Recheck if the DTC is set.
(1) Discharge the main drive lithium-ion battery as following procedures.
(1) Depress the brake pedal, and turn on the power supply mode of the electric motor switch (READY operation).
(2) Operate the air conditioning with MAX COOL.
(3) While confirming with BMU data list (item No. 5: Battery cell minimum voltage), discharge until the cell voltage becomes 4.1 volts or less.
(2) Erase the DTC.
(3) Turn off the power supply mode of the electric motor switch.
(4) Turn on the power supply mode of the electric motor switch without depressing the brake pedal.
(5) Wait for 5 minutes or more.
(6) Check if the DTC is set.
Is the DTC set?
Go to Step 3.
The procedure is complete.
 
STEP 3. Using scan tool (M.U.T.-IIISE), check the data list. <BMU>
Check the BMU's data list (refer to ).
  • Item No.393: Sum total time back up
Is the check result normal?
Go to Step 4.
Perform the BMU learning value manual written (Refer to GROUP 00 - Precautions before Service - Procedures for Writing BMU Learning Value ). Then go to Step 5.
 
STEP 4. Using scan tool (M.U.T.-IIISE), check whether the DTC is set again.
Recheck if the DTC is set.
(1) Measure the capacity of the main drive lithium-ion battery (Refer to ).
(2) Erase the DTC.
(3) Turn off the power supply mode of the electric motor switch.
(4) Turn on the power supply mode of the electric motor switch without depressing the brake pedal.
(5) Wait for 5 minutes or more.
(6) Check if the DTC is set.
Is the DTC set?
Replace the battery management unit (BMU) (Refer to ).
The procedure is complete.
 
STEP 5. Using scan tool (M.U.T.-IIISE), check whether the DTC is set again.
Recheck if the DTC is set.
(1) Erase the DTC.
(2) Turn off the power supply mode of the electric motor switch.
(3) Turn on the power supply mode of the electric motor switch without depressing the brake pedal.
(4) Wait for 5 minutes or more.
(5) Check if the DTC is set.
Is the DTC set?
Replace the battery management unit (BMU) (Refer to ).
The procedure is complete.