![[Previous]](../../../buttons/fprev.png)
![[Next]](../../../buttons/fnext.png)
| caution |
|
| caution | Disconnect the battery cable connection, and wait for 60 seconds or more before starting the work. |
).)
| note | Once disconnected from the instrument panel wiring harness, both electrodes of the clock spring connector short automatically. This prevents the driver's air bag from accidental deployment caused by static, etc. |
)
)
| note | The disconnection location should be sufficiently away from the harness side connector with consideration to the expansion harness connection location upon disconnections. |
)
| warning | If the glass is scratched, the glass may be shattered at deployment. Therefore, cover with a vehicle cover to avoid danger. |
| caution |
|
).| caution | Two connectors are installed to allow the passenger's air bag module to deploy in two stages. To ignite the 1st and 2nd squibs one after another, observe the following procedure: |
| caution | Disconnect the battery cable connection, and wait for 60 seconds or more before starting the work. |
).)
| note | When the passenger's (front) air bag module harness side connector is disconnected from the inflator, the two pins of inflator connector are automatically shorted. This prevents the unintentional deployment of passenger's (front) air bags caused by the static or others. |
)
| note | This is because the 2nd squib connector is different in shape. |
)
| note | This prevents the unintentional activation of inflator caused by the static or others. |
)
| warning | If the glass is scratched, the glass may be shattered at deployment. Therefore, cover with a vehicle cover to avoid danger. |
| caution |
|
).| caution | Disconnect the battery cable connection, and wait for 60 seconds or more before starting the work. |
).)
| note | When the harness side connector is disconnected from the inflator, the two pins of inflator connector are automatically shorted. This prevents the unintentional deployment of knee air bag caused by the static or others. |
| note | This prevents the unintentional deployment of knee air bag caused by the static or others. |
)
| warning | If the glass is scratched, the glass may be shattered at deployment. Therefore, cover with a vehicle cover to avoid danger. |
| caution |
|
).| caution | Disconnect the battery cable connection, and wait for 60 seconds or more before starting the work. |
)
| caution | Make sure to deploy both driver's and front passenger's side-airbags. |
| note | When the side-airbag module connector is disconnected from the floor harness, the two pins of side-airbag module connector are automatically shorted. This prevents the unintentional deployment of side-airbags caused by the static or others. |
)
| note | This prevents the air bags from unintentional deployment caused by static. |
| caution | The following procedures are intended to prevent the unintentional deployment caused by the static. Therefore, make sure to perform the procedures. |
)
| warning | If the glass is scratched, the glass may be shattered at deployment. Therefore, cover with a vehicle cover to avoid danger. |
| caution |
|
).| caution | Disconnect the battery cable connection, and wait for 60 seconds or more before starting the work. |
).)
| note | When the curtain air bag module connector is disconnected from the inflator, the two pins of inflator connector are automatically shorted. This prevents the unintentional deployment of curtain air bags caused by the static or others. |
| note | This prevents the unintentional deployment of curtain air bags caused by the static or others. |
)
| warning | If the glass is scratched, the glass may be shattered at deployment. Therefore, cover with a vehicle cover to avoid danger. |
| caution |
|
).| caution |
|
| caution | Disconnect the battery cable connection, and wait for 60 seconds or more before starting the work. |
| caution | When the connector is disconnected, the two pins of air bag module are automatically shorted to prevent the unintentional deployment caused by the static or others. However, in preparation for the accidental deployment, store the air bag module on a flat place with the deployment surface facing upward. Also, do not put anything on it. |
).| note | This prevents the unintentional activation of inflator caused by the static or others. |
)
)
)
)
| caution |
|
).| caution |
|
| caution | Before starting the work, wait for 60 seconds or more after the disconnection of the battery cable. (Refer to the item 5 of Service Precautions.) |
| caution | When the connector is disconnected, the two pins of air bag module are automatically shorted to prevent the unintentional deployment caused by the static or others. However, in preparation for the accidental deployment, store the air bag module on a flat place with the deployment surface facing upward. Also, do not put anything on it. |
).| note | This prevents the unintentional activation of inflator caused by the static or others. |
)
)
| note | The passenger's (front) air bag has a larger deployment volume than the driver's air bag. Therefore, it is necessary to tie the tires with rope. |
)
| caution |
|
).| caution |
|
| caution | Disconnect the battery cable connection, and wait for 60 seconds or more before starting the work. |
| caution | When the connector is disconnected, the two pins of air bag module are automatically shorted to prevent the unintentional deployment caused by the static or others. However, in preparation for the accidental deployment, store the air bag module on a flat place with the deployment surface facing upward. Also, do not put anything on it. |
).| note | This prevents the unintentional activation of inflator caused by the static or others. |
)
| caution |
|
).| caution |
|
| caution | Before starting the work, wait for 60 seconds or more after the disconnection of the battery cable. (Refer to the item 5 of Service Precautions.) |
).| note | This prevents the air bags from unintentional deployment caused by static. |
| caution | The following procedures are intended to prevent the unintentional deployment caused by the static. Therefore, make sure to perform the procedures. |
)
)
| caution |
|
).| caution |
|
| caution | Before starting the work, wait for 60 seconds or more after the disconnection of the battery cable. (Refer to the item 5 of Service Precautions.) |
| caution | When the connector is disconnected, the two pins of inflator are automatically shorted to prevent the unintentional activation caused by the static or others. However, in preparation for the accidental activation, store the air bag module on a flat place with the activation surface facing upward. Also, do not put anything on it. |
).| note | When the harness connector is disconnected from the inflator, the two pins of inflator connector are automatically shorted. This prevents the unintentional activation of inflator caused by the static or others. |
)
| note | This prevents the unintentional activation of inflator caused by the static or others. |
)
| caution |
|
).