[Previous][Next]
DTC No. P0C01-00 Front drive motor current-high
DTC No. P0C05-00 Front drive motor current deviation malfunction
 
 
danger
 
 
 
 
MONITOR EXECUTION
Continuous
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC set in memory for the item monitored below)
  • Not applicable
Sensor (The sensor below is determined to be normal)
  • Power drive unit current sensor
 
 
DTC SET CONDITIONS
Logic Flow Chart <DTC No. P0C01-00 (Judgment Criterion A)>
Logic Flow Chart <DTC No. P0C01-00 (Judgment Criterion B)>
Logic Flow Chart <DTC No. P0C05-00>
Check Condition A <DTC No. P0C01-00>
  • Power drive unit (FEMCU) power supply voltage is 8.0 volts or more.
  • IGBT status: ON
Judgment Criterion A <DTC No. P0C01-00>
  • The drive motor current-high switch is in ON condition three times or more.
Check Condition B <DTC No. P0C01-00>
  • Power drive unit (FEMCU) power supply voltage is 8.0 volts or more.
Judgment Criterion B <DTC No. P0C01-00>
  • The drive motor current-high switch is in ON condition for 0.4 second or more.
Check Condition A <DTC No. P0C05-00>
  • Power drive unit (FEMCU) power supply voltage is 8.0 volts or more.
  • The phase current order is 60 amperes or more.
  • The front motor speed is more than 400 rpm.
Judgment Criterion A <DTC No. P0C05-00>
  • The U/V/W phase current is between -32.8 amperes and 32.8 amperes for 0.40 second or more.
  • The U/V/W phase current is -32.8 amperes or more for 0.40 second or more.
  • The U/V/W phase current is 32.8 amperes or less for 0.40 second or more.
Check Condition B <DTC No. P0C05-00>
  • Power drive unit (FEMCU) power supply voltage is 8.0 volts or more.
  • The phase current order is 60 amperes or more.
  • The front motor speed is less than 3,000 rpm.
Judgment Criterion B <DTC No. P0C05-00>
  • The difference between the U/V/W phase current and U/V/W phase target current is in fail condition for 0.40 second or more.
 
 
OBD-II DRIVE CYCLE PATTERN
 
 
TROUBLESHOOTING HINTS
  • Malfunction of the power drive unit
  • Malfunction of the front motor
  • Malfunction of the three phase line
 
 
DIAGNOSIS
Required Special Tools:
  • MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
  • MB992745: V.C.I.-Lite main harness A
  • MB992747: V.C.I.-Lite USB cable short
  • MB992748: V.C.I.-Lite USB cable long
  • MB991223: Wiring harness set
  • MB992006: Extra fine probe
1.M.U.T.-IIISE other DTC check
Check whether the DTC, which has the higher priority than this DTC, is set. (Refer to DTC Inspection Priority Chart).
Is the DTC set?
Troubleshoot the set DTC (Refer to DIAGNOSTIC TROUBLE CODE CHART). Then,
 
2.Check of the high-voltage terminal (three phase line) of power drive unit
danger
  • Carry out the check on the high-voltage circuit while reading carefully the precautions on handling a high-voltage vehicle.
  • Wear the specified protection equipment during the check.
Check whether the high-voltage terminal of the front motor cable (three phase line) is connected to the power drive unit with the specified torque (Refer to POWER DRIVE UNIT REMOVAL AND INSTALLATION).
Is the check result normal?
Install the front motor cable (three phase line) with the specified torque (Refer to POWER DRIVE UNIT REMOVAL AND INSTALLATION). Then,
 
3.Visually check the front motor cable.
danger
  • Carry out the check on the high-voltage circuit while reading carefully the precautions on handling a high-voltage vehicle.
  • Wear the specified protection equipment during the check.
Visually check that there is no burnout, damage, foreign material on the front motor cable (three phase line).
Is the check result normal?
Replace the front motor (Refer to MOTOR (ELECTRIC MOTOR UNIT) REMOVAL AND INSTALLATION). Then,
 
4.Check of the insulation resistance of the power drive unit
danger
  • Carry out the check on the high-voltage circuit while reading carefully the precautions on handling a high-voltage vehicle.
  • Wear the specified protection equipment during the check.
Check the insulation resistance of the power drive unit (Refer to CHECK ON INSULATION RESISTANCE).
Is the check result normal?
Replace the power drive unit (Refer to POWER DRIVE UNIT REMOVAL AND INSTALLATION). Then,
 
5.Check of the insulation resistance of the front motor
danger
  • Carry out the check on the high-voltage circuit while reading carefully the precautions on handling a high-voltage vehicle.
  • Wear the specified protection equipment during the check.
Check the insulation resistance of the front motor (Refer to CHECK ON INSULATION RESISTANCE).
Is the check result normal?
Replace the front motor (Refer to MOTOR (ELECTRIC MOTOR UNIT) REMOVAL AND INSTALLATION). Then,
 
6.Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to OBD-II Drive Cycle OBD-II DRIVE CYCLE.
(2) Check the DTC.
Is the DTC set?
Replace the power drive unit (Refer to POWER DRIVE UNIT REMOVAL AND INSTALLATION). Then, go to.
The trouble can be an intermittent malfunction (Refer to General Information - How to Use Troubleshooting/Inspection Service Points, How to Cope with Intermittent Malfunctions HOW TO COPE WITH INTERMITTENT MALFUNCTIONS).
 
7.Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to OBD-II Drive Cycle OBD-II DRIVE CYCLE.
(2) Check the DTC.
Is the DTC set?
Replace the front motor (Refer to MOTOR (ELECTRIC MOTOR UNIT) REMOVAL AND INSTALLATION). Then,
The procedure is complete.
 
8.Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to OBD-II Drive Cycle OBD-II DRIVE CYCLE.
(2) Check the DTC.
Is the DTC set?
Retry the troubleshooting.
The procedure is complete.