[Previous][Next]
DTC P24BF-00: EVAP Leak Detection Pump Vacuum Switching Valve Circuit High
 
 
 
 
CIRCUIT OPERATION
  • Switching valve is built into the Evaporative Leak Check Module (ELCM).
  • MFI relay is built into the IPDM E/R.
  • The switching valve power is supplied from the MFI relay.
  • The ECM controls switching valve by turning the power transistor in the ECM "ON" and "OFF".
 
 
TECHNICAL DESCRIPTION
In response to a signal from the ECM, the switching valve switches the atmospheric side path of the evaporative emission canister to the reference path for the evaporative emission system leak monitor.
 
 
MONITOR EXECUTION
Continuous.
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC set in memory for the item monitored below)
  • Not applicable
Sensor (The sensor below is determined to be normal)
  • Not applicable
 
 
DTC SET CONDITIONS
Logic Flow Chart
Check Conditions
  • Power supply mode of electric motor switch is ON.
  • 12V battery positive voltage is between 10.0 and 16.5 volts.
Judgment Criterion
  • The coil current is 2 amperes or higher with the switching valve driving for 2 seconds.
 
 
FAIL-SAFE AND BACKUP FUNCTION
  • Prohibit introduction of purges.
  • Fuel filler lid cannot be opened even when pressing the fuel filler lid opener switch.
  • Indicates "REFUELING SYSTEM SERVICE REQUIRED" on the information screen in the multi-information display.
 
 
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function, OBD-II Drive Cycle – Pattern 1 OBD- II DRIVE CYCLE.
 
 
TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
  • Switching valve (built into the ELCM) failed.
  • Shorted switching valve circuit, harness damage or connector damage.
  • ECM failed.
 
 
DIAGNOSIS
Required Special Tools:
  • MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
  • MB992745: V.C.I.-Lite main harness A
  • MB992747: V.C.I.-Lite USB cable short
  • MB992748: V.C.I.-Lite USB cable long
1.STEP 1. Check of damage in wiring harness between ELCM connector terminal number 4 and ECM connector terminal number 80.
Q: Is the check result normal?
Repair or replace the connector, or repair the damaged harness wire.
 
2.STEP 2. Test the OBD-II drive cycle.
After erasing the DTC, carry out test drive with the drive cycle pattern, and recheck the DTC.
(1) Use scan tool (M.U.T.-III SE) to erase the DTC.
(2) Carry out test drive with the drive cycle pattern (Refer to Diagnostic Function, OBD-II Drive Cycle – Pattern 1 OBD- II DRIVE CYCLE).
(3) Use scan tool (M.U.T.-III SE) to recheck the DTC.
Q: Is DTC P24BF-00 set?
Replace the ELCM (Refer to ENGINE, Engine, Motor and Emission Control – Emission Control – Evaporative Emission System EVAPORATIVE EMISSION CANISTER REMOVAL AND INSTALLATION). Then
Intermittent malfunction (Refer to GENERAL INFORMATION, General Information – How to Use Troubleshooting/Inspection Service Points – How to Cope with Intermittent Malfunctions HOW TO COPE WITH INTERMITTENT MALFUNCTIONS).
 
3.STEP 3. Test the OBD-II drive cycle.
After erasing the DTC, carry out test drive with the drive cycle pattern, and recheck the DTC.
(1) Use scan tool (M.U.T.-III SE) to erase the DTC.
(2) Carry out test drive with the drive cycle pattern (Refer to Diagnostic Function, OBD-II Drive Cycle – Pattern 1 OBD- II DRIVE CYCLE).
(3) Use scan tool (M.U.T.-III SE) to recheck the DTC.
Q: Is DTC P24BF-00 set?
Replace the ECM (Refer to ENGINE CONTROL MODULE (ECM) REMOVAL AND INSTALLATION).
The inspection is complete.