[Previous][Next]
DTC P0016: Crankshaft/Camshaft Position Sensor Phase Problem
 
 
 
 
TECHNICAL DESCRIPTION
  • The ECM checks the variable valve timing system for malfunction.
 
 
DESCRIPTIONS OF MONITOR METHODS
  • The open timing of the intake valve is faster or slower than the specified value.
 
 
MONITOR EXECUTION
  • Continuous
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC set in memory for the item monitored below)
  • Not applicable
Sensor (The sensor below is determined to be normal)
  • Camshaft position sensor
  • Crankshaft position sensor
  • Engine coolant temperature sensor
  • Throttle position sensor
  • Engine oil control valve
 
 
DTC SET CONDITIONS
Logic Flow Chart
Check Conditions
  • Engine speed is between 594 r/min and 1,500 r/min.
  • Engine coolant temperature is between 20°C (68°F) and 88°C (190°F).
  • Engine oil control valve is "OFF".
  • 1 second has elapsed after the above mentioned conditions have been met.
Judgment Criterion
  • The open timing of the intake valve is faster than -11.2 degrees (ATDC) for 10 seconds.
or
  • The open timing of the intake valve is slower than 6.6 degrees (ATDC) for 10 seconds.
 
 
FAIL-SAFE AND BACKUP FUNCTION
  • None.
 
 
OBD-II DRIVE CYCLE PATTERN
  • Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 2 .
 
 
TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
  • Timing chain in out of place.
  • Loose timing chain.
  • Variable valve timing sprocket tooth coming off.
  • ECM failed.

 
 
DIAGNOSIS
Required Special Tools
  • MB991709: Test Harness
  • MB992110: Power Plant ECU Check Harness
STEP 1. Using the oscilloscope, measure output wave pattern at crankshaft position sensor and camshaft position sensor.
(1) Disconnect the crankshaft position sensor connector and connect the test harness special tool MB991709 between the separated connectors.
(2) Connect the oscilloscope probe to the crankshaft position sensor side connector terminal SGT.
(3) Disconnect the camshaft position sensor connector, and connect test harness special tool MB991709 between the separated connectors.
(4) Connect the oscilloscope probe to the camshaft position sensor side connector terminal CPI.
noteWhen measuring with the ECM side connector, disconnect all ECM connectors. Connect the check harness special tool MB992110 between the separated connectors. Then connect the oscilloscope probe to the check harness connector terminal SGT (crankshaft position sensor) and terminal CPI (camshaft position sensor).
(5) Set the vehicle to the continuous idling mode.
(6) Check the waveform.
  • The waveforms should be displayed on inspection procedure using an oscilloscope (Refer to ).
(7) Turn off the power supply mode of the electric motor switch.
Is the waveform normal?
Go to Step 2.
Go to Step 3.
 
STEP 2. Check the trouble symptoms.
(1) Carry out a test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 2 .
(2) Check the diagnostic trouble code (DTC).
Is DTC P0016 set?
Replace the ECM (Refer to Removal and Installation ). Then go to Step 4.
It can be assumed that this malfunction is intermittent. Refer to GROUP 00, How to Use Troubleshooting/ Inspection Service Points - How to Cope with Intermittent Malfunctions .
 
STEP 3. Check timing mark on the timing chain.
Is timing chain in out of place?
Repair it. Then initialize the learning value for the elongation of the timing chain. Refer to GROUP 00, Precautions Before Service - Timing Chain Learned Value Reset . Then go to Step 4.
  • Check the following items, and repair or replace the defective items.
    1. Check the timing chain loose.
    2. Check the variable valve timing sprocket tooth coming off.
  • Then initialize the learning value for the elongation of the timing chain. Refer to GROUP 00, Precautions Before Service - Timing Chain Learned Value Reset . Then go to Step 4.
 
STEP 4. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 2 .
(2) Check the diagnostic trouble code (DTC).
Is DTC P0016 set?
Retry the troubleshooting.
The inspection is complete.