Diagnosis Procedure

1.CHECK 12V BATTERY

Change the power supply mode of the electric motor switch to OFF, then disconnect the M.U.T.-III SE from the data link connector.
Close all the doors including the back door, then confirm that the room light turns off and wait for 3 minutes or more outside the vehicle in that state.
caution While waiting, do not touch the vehicle.
Check the connection of the 12V battery terminal (Refer to Precautions for Removing Battery Terminal).
Check the 12V battery terminal (Refer to Work Flow).

Is the inspection result normal?

Repair / replace harness or connector, securely lock the connector.

2.PERFORM SELF-DIAGNOSIS

M.U.T.-III SE

Connect the 12V battery terminal.
caution Do not set the vehicle to the READY status.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Repeat Step 2 twice or more.
caution Wait for 5 seconds or more after the power supply mode of the electric motor switch is changed to OFF.
Change the power supply mode of the electric motor switch to OFF, then disconnect the M.U.T.-III SE from the data link connector.
Close all the doors including the back door, then confirm that the room light turns off and wait for 3 minutes or more outside the vehicle in that state.
caution While waiting, do not touch the vehicle.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Start the M.U.T.-III SE, then erase the DTC set in "EBA".
Change the power supply mode of the electric motor switch to OFF, then disconnect the M.U.T.-III SE from the data link connector.
Close all the doors including the back door, then confirm that the room light turns off and wait for 3 minutes or more outside the vehicle in that state.
caution While waiting, do not touch the vehicle.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Depress the brake pedal 100 mm (3.9in) or more, the keep that state for 5 seconds or more.
Release the brake pedal.
Start the M.U.T.-III SE, then perform the self-diagnosis of "EBA".

Is DTC “C18ED-04” detected?

INSPECTION END

3.Checking connector terminal

Change the power supply mode of the electric motor switch to OFF, then disconnect the M.U.T.-III SE from the data link connector.
Close all the doors including the back door, then confirm that the room light turns off and wait for 3 minutes or more outside the vehicle in that state.
caution While waiting, do not touch the vehicle.
Disconnect the 12V battery negative terminal (Refer to Precautions for Removing Battery Terminal).
\Disconnect the electric driven intelligent brake unit wiring harness connector. Then, check that the pin terminal and its connection is normal.

Is the inspection result normal?

Repair / replace harness or connector, securely lock the connector.

4.PERFORM SELF-DIAGNOSIS

M.U.T.-III SE

Connect the 12V battery terminal.
caution Do not set the vehicle to the READY status.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Repeat Step 2 twice or more.
caution Wait for 5 seconds or more after the power supply mode of the electric motor switch is changed to OFF.
Change the power supply mode of the electric motor switch to OFF, then disconnect the M.U.T.-III SE from the data link connector.
Close all the doors including the back door, then confirm that the room light turns off and wait for 3 minutes or more outside the vehicle in that state.
caution While waiting, do not touch the vehicle.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Start the M.U.T.-III SE, then erase the DTC set in "EBA".
Change the power supply mode of the electric motor switch to OFF, then disconnect the M.U.T.-III SE from the data link connector.
Close all the doors including the back door, then confirm that the room light turns off and wait for 3 minutes or more outside the vehicle in that state.
caution While waiting, do not touch the vehicle.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Depress the brake pedal 100 mm (3.9in) or more, the keep that state for 5 seconds or more.
Release the brake pedal.
Start the M.U.T.-III SE, then perform the self-diagnosis of "EBA".

Is DTC “C18ED-04” detected?

INSPECTION END

5.CHECK 12V BATTERY

Change the power supply mode of the electric motor switch to OFF, then disconnect the M.U.T.-III SE from the data link connector.
Close all the doors including the back door, then confirm that the room light turns off and wait for 3 minutes or more outside the vehicle in that state.
caution While waiting, do not touch the vehicle.
Disconnect the 12V battery negative terminal (Refer to Precautions for Removing Battery Terminal).
Disconnect the electric driven intelligent brake unit wiring harness connector.
Connect the battery negative terminal.
Measure the voltage between the following terminals of the electric driven intelligent brake unit wiring harness connector.
Electric driven intelligent brake unit Voltage
Connecter Terminal
E417 26 – 32 10 – 16 V
Change the power supply mode of the electric motor switch to ON (READY indicator: OFF).
Measure the voltage between the following terminals of the electric driven intelligent brake unit wiring harness connector.
Electric driven intelligent brake unit Voltage
Connecter Terminal
E417 26 – 32 10 – 16 V

Electric driven intelligent brake unit	Voltage
E417	26 – 32	10 – 16 V

Electric driven intelligent brake unit	Voltage
E417	26 – 32	10 – 16 V

Is the inspection result normal?

6.Checking power supply to 12V battery circuit

Change the power supply mode of the electric motor switch to OFF, then disconnect the M.U.T.-III SE from the data link connector.
Close all the doors including the back door, then confirm that the room light turns off and wait for 3 minutes or more outside the vehicle in that state.
caution While waiting, do not touch the vehicle.
Disconnect the 12V battery negative terminal. Refer to Precautions for Removing Battery Terminal.
Check the 50 A fusible link (No. 26).
Check the continuity and short circuit between the electric driven intelligent brake unit wiring harness connector (terminal No. 26) and the 50 A fusible link (No. 26).
Check the 10 A fuse (No. 42).
Check the continuity and short circuit between the electric driven intelligent brake unit wiring harness connector (terminal No. 7) and the 10 A fuse (No. 42).

Is the inspection result normal?

Diagnose the 12V battery power supply. Refer to POWER DISTRIBUTION SYSTEM

Repair / replace harness or connector, securely lock the connector.

7.PERFORM SELF-DIAGNOSIS

M.U.T.-III SE

Connect the 12V battery terminal.
caution Do not set the vehicle to the READY status.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Repeat Step 2 twice or more.
caution Wait for 5 seconds or more after the power supply mode of the electric motor switch is changed to OFF.
Change the power supply mode of the electric motor switch to OFF, then disconnect the M.U.T.-III SE from the data link connector.
Close all the doors including the back door, then confirm that the room light turns off and wait for 3 minutes or more outside the vehicle in that state.
caution While waiting, do not touch the vehicle.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Start the M.U.T.-III SE, then erase the DTC set in "EBA".
Change the power supply mode of the electric motor switch to OFF, then disconnect the M.U.T.-III SE from the data link connector.
Close all the doors including the back door, then confirm that the room light turns off and wait for 3 minutes or more outside the vehicle in that state.
caution While waiting, do not touch the vehicle.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Depress the brake pedal 100 mm (3.9in) or more, the keep that state for 5 seconds or more.
Release the brake pedal.
Start the M.U.T.-III SE, then perform the self-diagnosis of "EBA".

Is DTC “C18ED-04” detected?

INSPECTION END

8.Checking ground

Change the power supply mode of the electric motor switch to OFF, then disconnect the M.U.T.-III SE from the data link connector.
Close all the doors including the back door, then confirm that the room light turns off and wait for 3 minutes or more outside the vehicle in that state.
caution While waiting, do not touch the vehicle.
Disconnect the 12V battery negative terminal (Refer to Precautions for Removing Battery Terminal).
Disconnect the electric driven intelligent brake unit wiring harness connector.
Check the continuity between the electric driven intelligent brake unit wiring harness connector (terminal No. 11) and body ground.
Electric driven intelligent brake unit − Continuity
Connecter Terminal
E417 11 Ground Continuity exists

Electric driven intelligent brake unit	−	Continuity
E417	11	Ground	Continuity exists

Is the inspection result normal?

Repair / replace harness or connector, securely lock the connector.

9.PERFORM SELF-DIAGNOSIS

M.U.T.-III SE

Connect the 12V battery terminal.
caution Do not set the vehicle to the READY status.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Repeat Step 2 twice or more.
caution Wait for 5 seconds or more after the power supply mode of the electric motor switch is changed to OFF.
Change the power supply mode of the electric motor switch to OFF, then disconnect the M.U.T.-III SE from the data link connector.
Close all the doors including the back door, then confirm that the room light turns off and wait for 3 minutes or more outside the vehicle in that state.
caution While waiting, do not touch the vehicle.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Start the M.U.T.-III SE, then erase the DTC set in "EBA".
Change the power supply mode of the electric motor switch to OFF, then disconnect the M.U.T.-III SE from the data link connector.
Close all the doors including the back door, then confirm that the room light turns off and wait for 3 minutes or more outside the vehicle in that state.
caution While waiting, do not touch the vehicle.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Depress the brake pedal 100 mm (3.9in) or more, the keep that state for 5 seconds or more.
Release the brake pedal.
Start the M.U.T.-III SE, then perform the self-diagnosis of "EBA".

Is DTC “C18ED-04” detected?

INSPECTION END

10.Check data monitor

M.U.T.-III SE

Connect the electric driven intelligent brake unit wiring harness connector.
Connect the battery negative terminal.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Repeat Step 3 twice or more.
caution Wait for 5 seconds or more after the power supply mode of the electric motor switch is changed to OFF.
Start the M.U.T.-III SE, then select "EBA" and "Data List" in order.
Check "iB Power Supply Battery" and "iB Power Supply ECU" (Refer to Reference Value) .

Is the inspection result normal?

Replace the electric driven intelligent brake unit (Refer to Exploded View

11.PERFORM SELF-DIAGNOSIS

M.U.T.-III SE

Connect the 12V battery terminal.
caution Do not set the vehicle to the READY status.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Repeat Step 2 twice or more.
caution Wait for 5 seconds or more after the power supply mode of the electric motor switch is changed to OFF.
Change the power supply mode of the electric motor switch to OFF, then disconnect the M.U.T.-III SE from the data link connector.
Close all the doors including the back door, then confirm that the room light turns off and wait for 3 minutes or more outside the vehicle in that state.
caution While waiting, do not touch the vehicle.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Start the M.U.T.-III SE, then erase the DTC set in "EBA".
Change the power supply mode of the electric motor switch to OFF, then disconnect the M.U.T.-III SE from the data link connector.
Close all the doors including the back door, then confirm that the room light turns off and wait for 3 minutes or more outside the vehicle in that state.
caution While waiting, do not touch the vehicle.
Change the power supply mode of the electric motor switch to ON from OFF without depressing the brake pedal.
caution Do not set the vehicle to the READY status.
Depress the brake pedal 100 mm (3.9in) or more, the keep that state for 5 seconds or more.
Release the brake pedal.
Start the M.U.T.-III SE, then perform the self-diagnosis of "EBA".

Is DTC “C18ED-04” detected?

Replace the electric driven intelligent brake unit. (Refer to Exploded View

INSPECTION END

Electric driven intelligent brake unit		Voltage
Connecter	Terminal	Voltage
E417	26 – 32	10 – 16 V