[Previous][Next]
DTC No. P0D3E-00: OBC AC input voltage sensor failure
DTC No. P0D3F-00: OBC voltage sensor failure(Circuit-low)
DTC No. P0D40-00: OBC voltage sensor failure(Circuit-high)
DTC No. P0D4E-00: OBC DC output voltage sensor failure(Circuit-low)
DTC No. P0D4F-00: OBC DC output voltage sensor failure(Circuit-high)
 
 
 
 
MONITOR EXECUTION
Continuous
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC set in memory for the item monitored below)
  • On Board Charger (OBC) monitor
  • EV CAN monitor <DTC No. P0D3E-00>
Sensor (The sensor below is determined to be normal)
  • Input voltage sensor <DTC No. P0D3E-00>
  • Not applicable <DTC No. P0D3F-00, P0D40-00, P0D4E-00, P0D4F-00>
 
 
DTC SET CONDITIONS
Logic Flow Chart <DTC No. P0D3E-00>
Logic Flow Chart <DTC No. P0D3F-00, P0D40-00, P0D4E-00, P0D4F-00>
 
 
Check condition <DTC No. P0D3E-00>
  • The vehicle status is in Propulsion system active for 1 second or more.
Check condition <DTC No. P0D3F-00, P0D40-00, P0D4E-00, P0D4F-00>
  • The On Board Charger (OBC)/DC-DC converter power supply voltage is 10.0 to 16.0 volts.
Judgment Criterion <DTC No. P0D3E-00>
  • The input voltage is more than 25 volts for 2 seconds or more.
Judgment Criterion <DTC No. P0D3F-00, DTC No. P0D4E-00>
  • The voltage is less than 0.299 volts for 0.5 second or more.
Judgment Criterion <DTC No. P0D40-00, DTC No. P0D4F-00>
  • The voltage is more than 4.686 volts for 0.5 second or more.
 
 
OBD-II DRIVE CYCLE PATTERN
 
 
TROUBLESHOOTING HINTS
  • Malfunction of the On Board Charger (OBC)/DC-DC converter
 
 
DIAGNOSIS
Required Special Tools:
  • MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
  • MB992745: V.C.I.-Lite main harness A
  • MB992747: V.C.I.-Lite USB cable short
  • MB992748: V.C.I.-Lite USB cable long
1.Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to OBD-II Drive Cycle OBD-II DRIVE CYCLE.
(2) Check the DTC.
Is the DTC set?
Replace the On Board Charger (OBC)/DC-DC converter (Refer to ON BOARD CHARGER (OBC) &DC-DC CONVERTER REMOVAL AND INSTALLATION). Then,
The trouble can be an intermittent malfunction (Refer to General Information - How to Use Troubleshooting/Inspection Service Points, How to Cope with Intermittent Malfunctions HOW TO COPE WITH INTERMITTENT MALFUNCTIONS).
 
2.Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to OBD-II Drive Cycle OBD-II DRIVE CYCLE.
(2) Check the DTC.
Is the DTC set?
Retry the troubleshooting.
The procedure is complete.