[Previous][Next]
DTC No. P0A32-00 Rear drive motor coil temperature sensor 1 Range check-min
DTC No. P0A33-00 Rear drive motor coil temperature sensor 1 Range check-max
DTC No. P30D3-17 RMCU Phase IGBT temperature sensor 1 Range check-max
DTC No. P30D4-16 RMCU Phase IGBT temperature sensor 1 Range check-min
DTC No. P30D6-17 RMCU Phase IGBT temperature sensor 2 Range check-max
DTC No. P30D7-16 RMCU Phase IGBT temperature sensor 2 Range check-min
DTC No. P30D9-17 RMCU Phase IGBT temperature sensor 3 Range check-max
DTC No. P30DA-16 RMCU Phase IGBT temperature sensor 3 Range check-min
DTC No. P30DC-17 RMCU Phase IGBT temperature sensor 4 Range check-max
DTC No. P30DD-16 RMCU Phase IGBT temperature sensor 4 Range check-min
DTC No. P30DF-17 RMCU Phase IGBT temperature sensor 5 Range check-max
DTC No. P30E0-16 RMCU Phase IGBT temperature sensor 5 Range check-min
DTC No. P30E2-17 RMCU Phase IGBT temperature sensor 6 Range check-max
DTC No. P30E3-16 RMCU Phase IGBT temperature sensor 6 Range check-min
DTC No. P30ED-17 Rear drive motor coil temperature sensor 2 Range check-max
DTC No. P30EE-16 Rear drive motor coil temperature sensor 2 Range check-min
DTC No. P30F0-17 RMCU capacitor temperature sensor Range check-max
DTC No. P30F1-16 RMCU capacitor temperature sensor Range check-min
DTC No. P30F4-17 RMCU control board temperature sensor Range check-max
DTC No. P30F5-16 RMCU control board temperature sensor Range check-min
 
 
 
 
MONITOR EXECUTION
Continuous
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC set in memory for the item monitored below)
  • Not applicable
Sensor (The sensor below is determined to be normal)
  • Not applicable
 
 
DTC SET CONDITIONS
Logic Flow Chart <DTC No.P0A32-00, P0A33-00, P30ED-17, P30EE-16>
Logic Flow Chart <DTC No.P30D3-17, P30D4-16, P30D6-17, P30D7-16, P30D9-17, P30DA-16, P30DC-17, P30DD-16, P30DF-17, P30E0-16, P30E2-17, P30E3-16>
Logic Flow Chart <DTC No.P30F0-17, P30F1-16>
Logic Flow Chart <DTC No.P30F4-17, P30F5-16>
Check Condition
  • REMCU power supply voltage is 8.0 volts or more
Judgment Criterion <DTC No.P0A32-00, P30EE-16>
  • The voltage is 0.065 volt or less for 0.5 second or more.
Judgment Criterion <DTC No.P0A33-00, P30ED-17>
  • The voltage is 4.761 volts or more for 0.5 second or more.
Judgment Criterion <DTC No.P30D3-17, P30D6-17, P30D9-17, P30DC-17, P30DF-17, P30E2-17>
  • The IGBT temperature (Duty) is 40°C (104°F) or less (75.5% or more) for 0.5 second or more.
Judgment Criterion <DTC No.P30D4-16, P30D7-16, P30DA-16, P30DD-16, P30E0-16, P30E3-16>
  • The IGBT temperature (Duty) is 200°C (392°F) or less (15.2% or more) for 0.5 second or more.
Judgment Criterion <DTC No.P30F0-17>
  • The voltage is 4.72 volts or more for 0.5 second or more.
Judgment Criterion <DTC No.P30F1-16>
  • The voltage is 0.067 volt or less for 0.5 second or more.
Judgment Criterion <DTC No.P30F4-17>
  • The voltage is 4.893 volts or more for 0.5 second or more.
Judgment Criterion <DTC No.P30F5-16>
  • The voltage is 0.072 volt or less for 0.5 second or more.
 
 
OBD-II DRIVE CYCLE PATTERN
 
 
TROUBLESHOOTING HINTS
  • Malfunction of the rear motor (malfunction of the REMCU)
 
 
DIAGNOSIS
Required Special Tools:
  • MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
  • MB992745: V.C.I.-Lite main harness A
  • MB992747: V.C.I.-Lite USB cable short
  • MB992748: V.C.I.-Lite USB cable long
1.Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to OBD-II Drive Cycle OBD-II DRIVE CYCLE.
(2) Check the DTC.
Is the DTC set?
Replace the rear motor assembly (Refer to MOTOR (ELECTRIC MOTOR UNIT) REMOVAL AND INSTALLATION). Then,
The trouble can be an intermittent malfunction (Refer to General Information - How to Use Troubleshooting/Inspection Service Points, How to Cope with Intermittent Malfunctions HOW TO COPE WITH INTERMITTENT MALFUNCTIONS).
 
2.Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to OBD-II Drive Cycle OBD-II DRIVE CYCLE.
(2) Check the DTC.
Is the DTC set?
Retry the troubleshooting.
The procedure is complete.