[Previous][Next]
Diagnosis Procedure
1.CHECK FUEL INJECTOR DRIVER POWER SUPPLY
  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Turn ignition switch ON.
  4. Check the voltage between ECM harness connector and ground.
    +Voltage
    ECM
    ConnectorTerminal
    F511GroundBattery voltage
Is the inspection result normal?
.
.
 
2.CHECK FUEL INJECTOR DRIVER POWER SUPPLY CIRCUIT
  1. Remove fuel injector relay.
  2. Check the continuity between ECM harness connector and fuel injector relay harness connector.
    +Continuity
    ECMFuel injector relay
    ConnectorTerminalConnectorTerminal
    F511F551Existed
  3. Also check harness for short to ground.
Is the inspection result normal?
.
Repair or replace error-detected parts
 
3.CHECK FUEL INJECTOR RELAY POWER SUPPLY (CONTACTOR SIDE)
Check the voltage between fuel injector relay harness connector and ground.
+Voltage
Fuel injector relay
ConnectorTerminal
F552GroundBattery voltage
Is the inspection result normal?
.
Perform the trouble diagnosis for power supply circuit.
 
4.CHECK FUEL INJECTOR RELAY POWER SUPPLY (COIL SIDE)
  1. Reconnect ECM harness connector.
  2. Turn ignition switch ON.
  3. Check the voltage between fuel injector relay harness connector and ground.
    +Voltage
    Fuel injector relay
    ConnectorTerminal
    F554GroundBattery voltage
Is the inspection result normal?
.
.
 
5.CHECK FUEL INJECTOR RELAY POWER SUPPLY CIRCUIT (COIL SIDE)
  1. Turn ignition switch OFF.
  2. Disconnect IPDM E/R harness connector.
  3. Check the continuity between IPDM E/R harness connector and fuel injector relay harness connector.
    +Continuity
    IPDM E/RFuel injector relay
    ConnectorTerminalConnectorTerminal
    F3573F554Existed
  4. Also check harness for short to ground.
Is the inspection result normal?
Perform the trouble diagnosis for power supply circuit.
Repair or replace error-detected parts.
 
6.CHECK FUEL INJECTOR RELAY GROUND CIRCUIT
  1. Turn ignition switch OFF.
  2. Check the continuity between fuel injector relay harness connector and ground.
    +Continuity
    Fuel injector relay
    ConnectorTerminal
    F553GroundExisted
  3. Also check harness for short to power.
Is the inspection result normal?
.
Repair or replace error-detected parts.
 
7.CHECK FUEL INJECTOR RELAY
Check the fuel injector relay. Refer to Component Inspection.
Is the inspection result normal?
Check intermittent incident. Refer to Intermittent IncidentIntermittent Incident.
Replace fuel injector relay.
 
8.CHECK ECM GROUND CIRCUIT
  1. Disconnect ECM harness connectors.
  2. Check the continuity between ECM harness connector and ground.
    ECMGroundContinuity
    ConnectorTerminal
    F514GroundExisted
    E16156
    157
    160
  3. Also check harness for short to power.
Is the inspection result normal?
.
Repair or replace error-detected parts.
 
9.CHECK FUEL INJECTOR CIRCUIT
  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between fuel injector harness connector and ECM harness connector.
    +Continuity
    Fuel injectorECM
    CylinderConnectorTerminalConnectorTerminal
    1F111F519Existed
    217
    2F12112
    220
    3F14112
    218
    4F1319
    219
  4. Also check harness for short to power and short to ground.
Is the inspection result normal?
.
Repair or replace error-detected parts.
 
10.CHECK FUEL INJECTOR
Check fuel injector. Refer to Component Inspection.
Is the inspection result normal?
Check intermittent incident. Refer to Intermittent IncidentIntermittent Incident.
Replace malfunctioning fuel injector. Refer to Removal and Installation.