[Previous][Next]
DTC B210D: Battery voltage low
DTC B210E: Battery voltage high
 
 
cautionIf DTC B210D, B210E is set in the occupant classification-ECU, always diagnose the CAN main bus lines.
 
 
TROUBLE JUDGMENT
The occupant classification-ECU sets DTC B210D if the power supply fuse voltage decreases to the specified value or less, and sets DTC B210E if the power supply fuse voltage increases to the specified value or more.
 
 
TECHNICAL DESCRIPTION (COMMENT)
The power supply fuse or the occupant classification-ECU may have a problem.
 
 
TROUBLESHOOTING HINTS
  • The power supply fuse may be defective.
  • The occupant classification-ECU may be defective.
  • The battery may be defective.
  • The wiring harness or connectors may have loose, corroded, or damaged terminals, or terminals pushed back in the connector
 
 
DIAGNOSIS
STEP 1. Measure the voltage at the occupant classification-ECU connector.
(1) Disconnect the occupant classification-ECU connector D-48-2.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between the occupant classification-ECU connector harness side connector terminal No. 13 and the body ground.
  • The voltage should measure 12 volts (battery positive voltage).
Is the measured voltage approximately 12 volts (battery positive voltage)?
Go to Step 7.
Go to Step 2.
 
STEP 2. Power supply fuse No.12 check.
Is the fuse in good condition?
Go to Step 4.
Go to Step 3.
 
STEP3. Check the harness wire for open circuit and short circuit between occupant classification-ECU connector D-38-2 (terminal No.13) and ETACS-ECU connector C-412 (terminal No.2).
Is the check result normal?
Replace the power supply fuse.
Repair the wiring harness. And then replace the power supply fuse.
 
STEP 4. Battery check.
Refer to GROUP 54A, Battery Test .
Is the check result normal?
Go to Step 5.
Charge (B210D only) or replace the battery.
 
STEP 5. Using scan tool MB991958, diagnose the CAN bus line.
cautionTo prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the scan tool ."
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the CAN bus line found to be normal?
Go to Step 6.
Repair the CAN bus line (Refer to GROUP 54C, Diagnosis ).
 
STEP 6. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1) Erase the DTC.
(2) Turn the ignition switch to "ON" position.
(3) Check if the DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the DTC set?
Go to Step 7.
There is an intermittent malfunction such as poor engaged connector(s) or open circuit (Refer to GROUP 00, How to Cope with Intermittent Malfunction ).
 
STEP 7. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1) Erase the DTC.
(2) Turn the ignition switch to the "ON" position.
(3) Check if the DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is DTC B210D or B210E set?
Replace the front seat cushion cover and pad assembly (Refer to GROUP 52A, Front Seat Assembly ).
There is an intermittent malfunction such as poor engaged connector(s) or open circuit (Refer to GROUP 00, How to Cope with Intermittent Malfunction ).