[Previous][Next]
REMOVAL AND INSTALLATION
 
 
Waterproof film removal steps 
•Door trim assembly (Refer to GROUP 52A - Door Trim .)
>>A<<1.Waterproof film
Door window glass runchannel removal steps
2.Door window glass runchannel
Door beltline weatherstrip inner removal steps
•Door trim assembly (Refer to GROUP 52A - Door Trim .)
3.Door beltline weatherstrip inner
Door speaker cover removal steps <Vehicles with audio amplifier> 
•Door trim assembly (Refer to GROUP 52A - Door Trim .)
>>A<<1.Waterproof film
4.Door speaker cover
Door beltline molding removal steps
•Door mirror assembly (Refer to GROUP 51 - Door Mirror .)
5.Door beltline molding
Door opening weatherstrip lower removal
6.Door opening weatherstrip lower
Door speaker bracket removal steps <Vehicles with audio amplifier> 
•Door trim assembly (Refer to GROUP 52A - Door Trim .)
>>A<<1.Waterproof film
7.Door speaker bracket
Front lower sash removal steps
•Door trim assembly (Refer to GROUP 52A - Door Trim .)
>>A<<1.Waterproof film
7.Door speaker bracket <Vehicles with audio amplifier>
8.Front lower sash
9.Door window glass runchannel rear
Door opening weatherstrip inner removal steps
•Cowl side trim and front scuff plate (Refer to GROUP 52A - Interior Trim .)
10.Door opening weatherstrip inner
Door opening weatherstrip outer removal steps
11.Door check connecting bolt
<<A>>12.Door opening weatherstrip outer
 
 
Waterproof film removal steps 
•Door trim assembly (Refer to GROUP 52A - Door Trim .)
>>B<<1.Waterproof film
Door window glass runchannel removal
2.Door window glass runchannel
Door beltline weatherstrip inner removal steps
•Door trim assembly (Refer to GROUP 52A - Door Trim .)
3.Door beltline weatherstrip inner
Door speaker cover A removal steps <Vehicles with audio amplifier>
•Door trim assembly (Refer to GROUP 52A - Door Trim .)
>>B<<1.Waterproof film
4.Door speaker cover A
Door beltline molding removal
5.Door beltline molding
Door opening weatherstrip lower removal
6.Door opening weatherstrip lower
Door speaker cover B removal steps <Vehicles with audio amplifier>
•Door trim assembly (Refer to GROUP 52A - Door Trim .)
>>B<<1.Waterproof film
7.Door speaker cover B
8.Door speaker cover B
Rear lower sash removal steps
•Door trim assembly (Refer to GROUP 52A - Door Trim .)
>>B<<1.Waterproof film
7.Door speaker cover B <Vehicles with audio amplifier>
8.Rear door damper
9.Rear lower sash
Door opening weatherstrip inner removal steps
•Rear scuff plate (Refer to GROUP 52A - Interior Trim .)
10.Door opening weatherstrip inner
Door opening weatherstrip outer removal steps
11.Door check connecting bolt
<<A>>12.Door opening weatherstrip outer
Rear door protect film lower removal <Vehicles with 18 inch tire>
>>A<<13.Rear door protect film lower
 
 
REMOVAL SERVICE POINT
 
 
<<A>> DOOR OPENING WEATHERSTRIP OUTER REMOVAL
Make the tool as shown in the figure, and remove the weatherstrip from the door panel.
 
 
 
 
INSTALLATION SERVICE POINT
 
 
>>A<< REAR DOOR PROTECT FILM LOWER INSTALLATION
1. Installation points
2. Installation procedures
caution
  • The ambient temperature should be 20 to 38°C (68 to 100°F). Ensure that the working area is clean.
  • If ambient temperature is less than 20°C (68°F), heat the rear door protect film lower and application surface to a temperature of 20 to 30°C (68 to 86°F).
  • Be careful that air bubbles are not formed under the rear door protect film lower.
(1) Use Parts Cleaner (MZ100387 or equivalent) to degrease the rear door protect film lower application surface.
(2) Remove backing paper from the rear door protect film lower, and apply it to the specified position.
 
 
 
>>B<< WATERPROOF FILM INSTALLATION
cautionWhen a waterproof film is applied, guide the butyl rubber tape under the inner panel drain hole.
Apply the specified adhesive to the water-proof film as shown in the figure and stick the film.
Butyl rubber tape: 3M™ AAD Part number 8633 or equivalent