[Previous][Next]
DTC P0183: Fuel Tank Temperature Sensor Circuit High Input

 
 
 
 
CIRCUIT OPERATION
  • 5-volt voltage is applied to the fuel tank temperature sensor output terminal (terminal No. 3) from the ECM (terminal No. 115) via the resistor in the ECM.
  • The fuel tank temperature sensor output voltage increases when the resistance increases and decreases when the resistance decreases. The ground terminal (terminal No. 1) is grounded to the vehicle body.
 
 
TECHNICAL DESCRIPTION
  • The fuel tank temperature sensor converts the fuel tank temperature to a voltage.
  • The ECM detects the fuel tank temperature with this output voltage.
 
 
DESCRIPTIONS OF MONITOR METHODS
  • Fuel tank temperature sensor output voltage is out of specified range.
 
 
MONITOR EXECUTION
  • Continuous
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC set in memory for the item monitored below)
  • Not applicable
Sensor (The sensor below is determined to be normal)
  • Not applicable
 
 
DTC SET CONDITIONS
Logic Flow Chart
 
 
Check Condition
  • More than 2 seconds have passed since the engine starting sequence was completed.
Judgment Criterion
  • Fuel tank temperature sensor output voltage is more than 4.6 volts for 2 seconds.
 
 
FAIL-SAFE AND BACKUP FUNCTION
  • None
 
 
OBD-II DRIVE CYCLE PATTERN
  • Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 23 .
 
 
TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
  • Fuel tank temperature sensor failed.
  • Open fuel tank temperature sensor circuit, harness damage, or connector damage.
  • ECM failed.

 
 
DIAGNOSIS
Required Special Tools:
  • MB991958: Scan Tool (M.U.T.-III Sub Assembly)
    • MB991824: V.C.I.
    • MB991827: USB Cable
    • MB991910: Main Harness A
  • MB992110: Power Plant ECU Check Harness
STEP 1. Using scan tool MB991958, check data list item 53: Fuel Tank Temperature Sensor.
cautionTo prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to the data reading mode for item 53, Fuel Tank Temperature Sensor.
  • Approximately the same as the ambient air temperature when the engine is cooled.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the sensor operating properly?
It can be assumed that this malfunction is intermittent. Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions .
Go to Step 2.
 
STEP 2. Check harness connector D-24 at fuel pump module for damage.
Is the harness connector in good condition?
Go to Step 3.
Repair or replace it. Refer to GROUP 00E, Harness Connector Inspection . Then go to Step 9.
 
STEP 3. Check the fuel tank temperature sensor.
(1) Disconnect the fuel pump module connector D-24.
(2) Measure the resistance between terminal No. 1 and No. 3 of the fuel pump module.
Standard value: 0.5 - 12.0 kΩ
Is the measured resistance between 0.5 and 12.0 kΩ?
Go to Step 4.
Replace the fuel pump module. Then go to Step 9.
 
STEP 4. Measure the sensor supply voltage at fuel pump module harness side connector D-24.
(1) Disconnect the connector D-24 and measure at the harness side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 3 and ground.
  • Voltage should be between 4.5 and 4.9 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the measured voltage between 4.5 and 4.9 volts?
Go to Step 7.
Go to Step 5.
 
STEP 5. Check harness connector B-27 at ECM for damage.
Is the harness connector in good condition?
Go to Step 6.
Repair or replace it. Refer to GROUP 00E, Harness Connector Inspection . Then go to Step 9.
 
STEP 6. Measure the sensor supply voltage at ECM connector B-27 by using power plant ECU check harness special tool MB992110.
(1) Disconnect all ECM connectors. Connect the power plant ECU check harness special tool MB992110 between the separated connectors.
(2) Disconnect the fuel pump module connector D-24.
(3) Turn the ignition switch to the "ON" position.
(4) Measure the voltage between terminal No. 115 and ground.
  • Voltage should be between 4.5 and 4.9 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Is the measured voltage between 4.5 and 4.9 volts?
Check harness connector C-28 at intermediate connector for damage, and repair or replace as required. Refer to GROUP 00E, Harness Connector Inspection . If intermediate connector is in good condition, repair harness wire between fuel pump module connector D-24 (terminal No. 3) and ECM connector B-27 (terminal No. 115) because of open circuit. Then go to Step 9.
Go to Step 8.
 
STEP 7. Check the continuity at fuel pump module harness side connector D-24.
(1) Disconnect the connector D-24 and measure at the harness side.
(2) Check for the continuity between terminal No. 1 and ground.
  • Continuity (2 ohms or less)
Does continuity exist?
Go to Step 8.
Repair harness wire between fuel pump module connector D-24 (terminal No. 1) and ground because of open circuit. Then go to Step 9.
 
STEP 8. Using scan tool MB991958, check data list item 53: Fuel Tank Temperature Sensor.
(1) Turn the ignition switch to the "ON" position.
(2) Set scan tool MB991958 to the data reading mode for item 53, Fuel Tank Temperature Sensor.
  • Approximately the same as the ambient air temperature when the engine is cooled.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Is the sensor operating properly?
It can be assumed that this malfunction is intermittent. Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions .
Replace the ECM (Refer to, Removal and Installation ). Then go to Step 9.
 
STEP 9. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 23 .
(2) Check the diagnostic trouble code (DTC).
Is DTC P0183 set?
Retry the troubleshooting.
The inspection is complete.