[Previous][Next]
DTC P0AF5: IGBT1 temperature sensor fails (short to power supply, short circuit)
DTC P0AF4: IGBT1 temperature sensor fails (short to ground, open circuit)
DTC P103A: IGBT2 temperature sensor fails (short to power supply, short circuit)
DTC P103B: IGBT2 temperature sensor fails (short to ground, open circuit)
DTC P103D: IGBT3 temperature sensor fails (short to power supply, short circuit)
DTC P103E: IGBT3 temperature sensor fails (short to ground, open circuit)
DTC P1069: Condenser temperature sensor fails (short to power supply, short circuit)
DTC P106A: Condenser temperature sensor fails (short to ground, open circuit)
DTC P1016: CPU ambient temperature sensor fails (short to power supply, short circuit)
DTC P1017: CPU ambient temperature sensor fails (short to ground, open circuit)
 
 
 
 
MONITOR EXECUTION
  • Continuous
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
  • Not applicable
Sensor (The sensor below is determined to be normal)
  • Not applicable
 
 
DTC SET CONDITIONS
Logic Flow Chart <DTC P0AF5, P0AF4, P103A, P103B, P103D, P103E>
Check Conditions <DTC P0AF5, P0AF4, P103A, P103B, P103D, P103E>
  • REMCU power supply voltage is 8 volts to 16 volts.
Judgment Criterion <DTC P0AF5, P103A, P103D>
  • Change of the REMCU IGBT temperature sensor voltage is more than 4.8 volts [201°C (394°F)] for 0.5 second.
Judgment Criterion <DTC P0AF4, P103B, P103E>
  • Change of the REMCU voltage is less than 0.182 volt [-51°C (-60°F)] for 0.5 second.
 
 
Logic Flow Chart <DTC P1069, P106A>
Check Conditions <DTC P1069, P106A>
  • REMCU power supply voltage is 8 volts to 16 volts.
Judgment Criterion <DTC P1069>
  • Change of the REMCU capacitor temperature sensor voltage is more than 4.761 volts [201°C (394°F)] for 0.5 second.
Judgment Criterion <DTC P106A>
  • Change of the REMCU voltage is less than 0.072 volt [-51°C (-60°F)] for 0.5 second.
 
 
Logic Flow Chart <DTC P1016, P1017>
Check Conditions <DTC P1016, P1017>
  • REMCU power supply voltage is 8 volts to 16 volts.
Judgment Criterion <DTC P1016>
  • Change of the REMCU control module temperature sensor voltage is more than 4.75 volts [201°C (394°F)] for 0.5 second.
Judgment Criterion <DTC P1017>
  • Change of the REMCU voltage is less than 0.067 volt [-51°C (-60°F)] for 0.5 second.
 
 
OBD-II DRIVE CYCLE PATTERN
  • Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 1 .
 
 
PROBABLE CAUSES
Malfunction of the REMCU
 
 
DIAGNOSIS
STEP 1. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 1 .
(2) Check the DTC.
Is the DTC set?
Replace the REMCU (Refer to ). Then go to Step 2.
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points, - How to Cope with Intermittent Malfunctions ).
 
STEP 2. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 1 .
(2) Check the DTC.
Is the DTC set?
Retry the troubleshooting.
The inspection is complete.