[Previous][Next]
Inspection procedure 4: Starts up and dies
 
 
 
 
COMMENT
  • In such cases as the above, the cause is usually improper air/fuel mixture. It is possible, though less likely, that the spark plugs are generating sparks but the sparks are weak.
 
 
TROUBLESHOOTING HINTS (The most likely causes for this case:)
  • Fuel pump system failed.
  • Ignition system failed.
  • Injector system failed.
  • Poor compression.
  • EGR system failed.
  • Contaminated fuel.
  • Dirtiness around throttle valve.
  • ECM failed.

 
 
DIAGNOSIS
STEP 1. Check if the EGR valve sounds during initialization.
Is the initialization sound heard in the EGR valve?
Go to Step 2.
Refer to GROUP 17, Emission Control - Exhaust Gas Recirculation (EGR) System - EGR Valve (stepper motor) Check .
 
STEP 2. Using scan tool (M.U.T.-IIISE), read the diagnostic trouble code (DTC).
cautionTo prevent damage to scan tool (M.U.T.-IIISE), always turn off the power supply mode of the electric motor switch before connecting or disconnecting scan tool (M.U.T.-IIISE).
(1) Connect scan tool (M.U.T.-IIISE). Refer to HOW TO CONNECT THE SCAN TOOL (M.U.T.-IIISE) .
(2) Turn on the power supply mode of the electric motor switch.
(3) Read the DTC.
(4) Turn off the power supply mode of the electric motor switch.
Is any DTC set?
Refer to Diagnostic Trouble Code Chart .
Go to Step 3.
 
STEP 3. Using scan tool (M.U.T.-IIISE), check data list.
(1) Turn on the power supply mode of the electric motor switch.
(2) Check the following items in the data list. Refer to Data List Reference Table .
  1. Item 1: Power Supply Voltage
  2. Item 6: Engine Coolant Temperature Sensor
(3) Turn off the power supply mode of the electric motor switch.
Is the sensor operating properly?
Go to Step 4.
Repair or replace it. Then confirm that the malfunction symptom is eliminated.
 
STEP 4. Using scan tool (M.U.T.-IIISE), check actuator test.
(1) Turn on the power supply mode of the electric motor switch.
(2) Set scan tool (M.U.T.-IIISE) to the actuator test mode for item 9, Fuel Pump.
  • An operation sound of the fuel pump should be heard.
(3) Turn off the power supply mode of the electric motor switch.
Is the actuator operating properly?
Go to Step 5.
Repair or replace it. Then confirm that the malfunction symptom is eliminated.
 
STEP 5. Inspection of throttle body (throttle valve area) for dirtiness.
Is the throttle valve area dirty?
Refer to Throttle Body (throttle valve area) Cleaning .
Go to Step 6.
 
STEP 6. Check the ignition timing.
Refer to GROUP 11A, On-vehicle Service - Ignition Timing Check .
Is the ignition timing normal?
Go to Step 7.
Check for installed conditions of the timing chain. Then confirm that the malfunction symptom is eliminated.
 
STEP 7. Check the fuel pressure.
Refer to Fuel Pressure Test .
Is the fuel pressure normal?
Go to Step 8.
Repair it. Then confirm that the malfunction symptom is eliminated.
 
STEP 8. Check the injector.
Refer to Injector check .
Is the measured resistance normal?
Go to Step 9.
Replace the faulty injector. Then confirm that the malfunction symptom is eliminated.
 
STEP 9. Check of harness damage in power supply line between MFI relay connector and injector connector.
Are the harness wires in good condition?
Go to Step 10.
Repair the connector(s) or wiring harness. Then confirm that the malfunction symptom is eliminated.
 
STEP 10. Check the spark plugs.
Refer to GROUP 16, Ignition System - On-vehicle Service - Spark Plug Check and Cleaning .
Are there any abnormalities?
Replace the spark plug. Then confirm that the malfunction symptom is eliminated.
Go to Step 11.
 
STEP 11. Check the ignition coil.
Refer to GROUP 16, Ignition System - On-vehicle Service - Ignition Coil Check .
Are there any abnormalities?
Replace the ignition coil. Then confirm that the malfunction symptom is eliminated.
Go to Step 12.
 
STEP 12. Check the compression pressure.
Refer to GROUP 11A, On-vehicle Service - Compression Pressure Check .
Is the compression pressure normal?
  • Check the following items, and repair or replace the defective items.
    1. Check fuel lines for clogging.
    2. Check if fuel is contaminated.
    3. Check if the injectors are clogged.
  • Then confirm that the malfunction symptom is eliminated.
Repair it. Then confirm that the malfunction symptom is eliminated.