DTC P0138: Heated Oxygen Sensor (rear) Circuit High Voltage
CIRCUIT OPERATION
A voltage corresponding to the oxygen concentration in the exhaust gas is sent to the ECM terminal O2RL from the output terminal of the heated oxygen sensor (rear).
Terminal ORLE line of the heated oxygen sensor (rear) is grounded with ECM terminal ORLE.
The ECM applies an offset voltage of 0.5 volt to ground terminal of the heated oxygen sensor (rear).
TECHNICAL DESCRIPTION
The output signal of the linear air-fuel ratio sensor is compensated by the output signal of the heated oxygen sensor (rear).
The ECM checks for the heated oxygen sensor (rear) output voltage.
DESCRIPTIONS OF MONITOR METHODS
Heated oxygen sensor (rear) output voltage is over specified range.
MONITOR EXECUTION
Continuous
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
Linear air-fuel ratio sensor monitor
Linear air-fuel ratio sensor heater monitor
Heated oxygen sensor (rear) heater monitor
Heated oxygen sensor offset voltage monitor
Sensor (The sensor below is determined to be normal)
Mass airflow sensor
Engine coolant temperature sensor
Intake air temperature sensor
Barometric pressure sensor
Throttle position sensor
DTC SET CONDITIONS
Logic Flow Chart
Check Conditions
Heated oxygen sensor offset voltage is between 0.4 and 0.6 volt.
2 seconds or more have passed since the engine starting sequence was completed.
Judgment Criterion
Heated oxygen sensor (rear) output voltage has continued to be 1.8 volts or higher for 2 seconds.
FAIL-SAFE AND BACKUP FUNCTION
None
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 23 .
TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
Shorted heated oxygen sensor (rear) circuit, or connector damage.
ECM failed.
DIAGNOSIS
Required Special Tools:
MB992744: Vehicle Communication Interface-Lite (V.C.I.-Lite)
MB992745: V.C.I.-Lite Main Harness A
MB992747: V.C.I.-Lite USB Cable Short
MB992748: V.C.I.-Lite USB Cable Long
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
MB991824: Vehicles Communication Interface (V.C.I.)
MB991827: M.U.T.-III USB Cable
MB991910: M.U.T.-III Main Harness A (Vehicles with CAN communication system)
STEP 1. Using scan tool (M.U.T.-III), check data list item AD: Heated Oxygen Sensor (rear).
caution
To prevent damage to scan tool (M.U.T.-III), always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool (M.U.T.-III).
(1) Connect scan tool (M.U.T-III). Refer to HOW TO CONNECT THE SCAN TOOL (M.U.T.-III) .
(2) Start the engine and run at idle.
(3) Set scan tool (M.U.T-III) to the data reading mode for item AD, Heated Oxygen Sensor (rear).
Transaxle: 2nd
Drive with wide open throttle
Engine: 3,500 r/min or more
The output voltages should be between 0.6 and 1.0 volt.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the sensor operating properly?
It can be assumed that this malfunction is intermittent. Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions .
Go to Step 2.
STEP 2. Check of short circuit to power supply in O2RL line between heated oxygen sensor (rear) connector and ECM connector.
Is the harness wire in good condition?
Replace the ECM (Refer to Removal and Installation ). Then go to Step 4.
Repair the connector(s) or wiring harness. Then go to Step 3.
STEP 3. Using scan tool (M.U.T.-III), check data list item AD: Heated Oxygen Sensor (rear).
(1) Start the engine and run at idle.
(2) Set scan tool (M.U.T.-III) to the data reading mode for item AD, Heated Oxygen Sensor (rear).
Transaxle: 2nd speed
Drive with wide open throttle
Engine: 3,500 r/min or more
The output voltages should be between 0.6 and 1.0 volt.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Is the sensor operating properly?
It can be assumed that this malfunction is intermittent. Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions .
Replace the ECM (Refer to Removal and Installation ). Then go to Step 4.
STEP 4. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 23 .