[Previous][Next]
DTC P014E: Linear Air-Fuel Ratio Sensor Circuit Slow Response - Rich to Lean (bank 2, sensor 1)
 
 
 
 
TECHNICAL DESCRIPTION
  • The ECM effects air/fuel ratio feedback control in accordance with the signals from the left bank linear air-fuel ratio sensor.
  • If the left bank linear air-fuel ratio sensor has deteriorated, corrections will be made by the heated oxygen sensor (rear).
 
 
DESCRIPTIONS OF MONITOR METHODS
  • When the average of the difference between the response times of the rich side and the lean side of the left bank linear air-fuel ratio sensor during the monitoring time becomes equal to or higher than the predetermined value, the DTC is set as the left bank linear air-fuel ratio sensor deterioration.
 
 
MONITOR EXECUTION
  • Continuous
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC set in memory for the item monitored below)
  • Left bank linear air-fuel ratio sensor heater monitor
  • Misfire monitor
  • Fuel system monitor
Sensor (The sensor below is determined to be normal)
  • Mass airflow sensor
  • Engine coolant temperature sensor
  • Intake air temperature sensor
  • Barometric pressure sensor
  • Throttle position sensor
  • Accelerator pedal position sensor
 
 
DTC SET CONDITIONS
Logic Flow Chart
 
 
Check Conditions
  • Engine speed is between 1,188 and 3,000 r/min.
  • Volumetric efficiency is between 21.8 and 68.8 percent.
  • Mass airflow sensor output is 8 g/sec or more.
  • Engine coolant temperature is more than 60°C (140°F).
  • Under the closed loop air/fuel control.
  • The accelerator pedal is depressed.
  • Short-term fuel trim is between -25 and +25 percent.
  • More than 3 seconds have passed after the above mentioned conditions have been met.
  • Left bank linear air-fuel ratio sensor signal length is 2.50 or less.
  • During the drive cycle, the ECM performs monitoring with the accumulated total time of 10 seconds, 3 times.
Judgment Criteria
  • The average response time ratio (to lean time/to rich time) is more than specified value.
  • The amount of compensated air/fuel ratio based on the heated oxygen sensor (rear) is out of specified amount.
 
 
FAIL-SAFE AND BACKUP FUNCTION
  • None
 
 
OBD-II DRIVE CYCLE PATTERN
  • Refer to Diagnosis Function - OBD-II Drive Cycle - Pattern 1 .
 
 
TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
  • Left bank linear air-fuel ratio sensor failed.

 
 
DIAGNOSIS
Required Special Tools:
  • MB992744: Vehicle Communication Interface-Lite (V.C.I.-Lite)
  • MB992745: V.C.I.-Lite Main Harness A
  • MB992747: V.C.I.-Lite USB Cable Short
  • MB992748: V.C.I.-Lite USB Cable Long
  • MB991958: Scan Tool (M.U.T.-III Sub Assembly)
    • MB991824: Vehicles Communication Interface (V.C.I.)
    • MB991827: M.U.T.-III USB Cable
    • MB991910: M.U.T.-III Main Harness A (Vehicles with CAN communication system)
STEP 1. Test the OBD-II drive cycle.
cautionTo prevent damage to scan tool (M.U.T.-III), always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool (M.U.T.-III).
(1) Connect scan tool (M.U.T.-III). Refer to HOW TO CONNECT THE SCAN TOOL (M.U.T.-III) .
(2) Turn the ignition switch to the "ON" position and delete the DTC.
(3) Carry out the test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 1 .
(4) Check the diagnostic trouble code (DTC).
Is DTC P014E set?
Replace the left bank linear air-fuel ratio sensor. Then go to Step 2.
It can be assumed that this malfunction is intermittent. Refer to GROUP 00, How to Use Troubleshooting/ Inspection Service Points - How to Cope with Intermittent Malfunctions .
 
STEP 2. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 1 .
(2) Check the diagnostic trouble code (DTC).
Is DTC P014E set?
Retry the troubleshooting.
The inspection is complete.