[Previous][Next]
DTC U0245 NAVI/DISP.AUDIO CAN timeout
 
 
caution
  • If DTC U0245 is set in the ETACS-ECU, always diagnose the CAN bus line.
  • Before replacing the ECU or multivision display <Vehicles with smartphone link display audio>, ensure that the power supply circuit, the ground circuit and the communication circuit are normal.
 
 
DIAGNOSTIC FUNCTION
When the signals from multivision display <Vehicles with smartphone link display audio> cannot be received, the ETACS-ECU sets DTC U0245.
 
 
JUDGMENT CRITERIA
After the following statuses continue to be true for 5 seconds, if the communication with the multivision display <Vehicles with smartphone link display audio> be established for 2,500 ms or more, the ETACS-ECU determines that a problem has occurred.
  • No abnormality is present to the network.
  • Ignition switch is in the "ON" position.
  • No abnormality is present to the power supply fuse (IOD fuse), or the odometer value is at 80.5 km (50.0 miles) or more.
  • ETACS-ECU system voltage is at 10-16 volts.
 
 
TROUBLESHOOTING HINTS
  • The multivision display <Vehicles with smartphone link display audio> may be defective
  • The ETACS-ECU may be defective
  • The CAN bus line may be defective
 
 
DIAGNOSIS
STEP 1. Using scan tool (M.U.T.-IIISE), diagnose the CAN bus line.
(1)
cautionTo prevent damage to scan tool (M.U.T.-IIISE), always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool (M.U.T.-IIISE).
Connect scan tool (M.U.T.-IIISE). Refer to "How to connect the Scan Tool (M.U.T.-IIISE) ."
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the CAN bus line found to be normal?
Go to Step 2.
Repair the CAN bus line (Refer to GROUP 54C - Troubleshooting ).
 
STEP 2. Confirm the option coding.
Confirm whether the option coding corresponds to an actual vehicle equipment.
Is the check result normal?
Go to Step 3.
Configure the option coding again.
 
STEP 3. Using scan tool (M.U.T.-IIISE), read the other system DTC.
Check if DTC is set in the multivision display <Vehicles with smartphone link display audio>.
Is the DTC set?
Perform the DTC troubleshooting to the multivision display <Vehicles with smartphone link display audio>.
Go to Step 4.
 
STEP 4. Using scan tool (M.U.T.-IIISE), read the other system DTC.
Check if DTC U0245 is set in the KOS&OSS-ECU.
Is the DTC set?
Go to Step 5.
Go to Step 6.
 
STEP 5. Using scan tool (M.U.T.-IIISE), read the DTC again.
Check again if the DTC is set in the ETACS-ECU.
(1) Erase the DTC.
(2) Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
(3) Check if DTC is set.
Is the DTC set?
Replace the multivision display <Vehicles with smartphone link display audio>.
The trouble can be an intermittent malfunction such as a poor connection or open circuit in the CAN bus lines between the multivision display <Vehicles with smartphone link display audio> and the ETACS-ECU (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).
 
STEP 6. Using scan tool (M.U.T.-IIISE), read the DTC again.
Check again if the DTC is set in the ETACS-ECU.
(1) Erase the DTC.
(2) Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
(3) Check if DTC is set.
Is the DTC set?
Replace the ETACS-ECU.
The trouble can be an intermittent malfunction such as a poor connection or open circuit in the CAN bus lines between the multivision display <Vehicles with smartphone link display audio> and the ETACS-ECU (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).