[Previous][Next]
DTC B1130 Ignition power supply
 
 
caution
  • If DTC B1130 is set, always diagnose the CAN bus lines.
  • Before replacing ECU, ensure that the communication circuit is normal.
 
 
DIAGNOSTIC FUNCTION
If the output power supply status is different from the engine switch status information received from ETACS-ECU via CAN, KOS&OSS-ECU sets DTC B1130. At the same time, KOS&OSS-ECU displays the power supply system error warning to the combination meter, and flashes the indicator of engine switch in amber.
 
 
JUDGMENT CRITERIA
Check Conditions
  • The terminal voltage of IOD and +B is between 10 and 16 volts.
Judgment Criterion
  • Any of the following conditions is met, and 2 seconds or more have elapsed.
    1. The engine switch status information received from ETACS-ECU is ACC when the power supply mode is at ON.
    2. The engine switch status information received from ETACS-ECU is OFF when the power supply mode is at ON.
    3. The engine switch status information received from ETACS-ECU is ON when the power supply mode is at OFF.
    4. The engine switch status information received from ETACS-ECU is ON when the power supply mode is at ACC.
 
 
PROBABLE CAUSES
  • Malfunction of the CAN bus line
  • Damaged wiring harness or connector (short to ground or short to power supply or open circuit in IG1 line)
  • Malfunction of KOS&OSS-ECU
  • Malfunction of ETACS-ECU
 
 
DIAGNOSIS
STEP 1. Using scan tool (M.U.T.-IIISE), diagnose the CAN bus line
After performing the forced power supply output (Refer to ) "IG ON" using the scan tool (M.U.T.-IIISE), diagnose the CAN bus line.
Is the check result normal?
Go to Step 2.
Repair the CAN bus line (Refer to GROUP 54C - Diagnosis ).
 
STEP 2. Using scan tool (M.U.T.-IIISE), check the DTC.
Check if KOS&OSS-ECU DTC B1133 is set.
Is the DTC set?
Troubleshoot for the relevant DTC (Refer to ).
Go to Step 3.
 
STEP 3. Voltage measurement at ETACS-ECU connector (IGS line)
(1) Disconnect the connector, and measure at the wiring harness side.
(2) Turn the engine switch from "OFF" position to "ON" position.
(3) Measure the voltage between the ETACS-ECU connector (IGS line) and the body ground.
OK: The voltage should measure approximately 12 volts (battery positive voltage).
(4) Turn the engine switch from "ON" position to "OFF" position.
(5) Measure the voltage between the ETACS-ECU connector (IGS line) and the body ground.
OK: 1 volt or less
Is the check result normal?
Go to Step 5.
Go to Step 4.
 
STEP 4. Check of short to power supply, short to ground or open circuit in IG1 line between the KOS&OSS-ECU connector and the ETACS-ECU connector
Is the check result normal?
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).
Repair the connector(s) or wiring harness.
 
STEP 5. Using scan tool (M.U.T.-IIISE), check the other system data list
Operate the engine switch to change the power supply mode, and check that the data list display of ETACS-ECU is changed.
  • When power supply mode is "OFF."
 
ETACS-ECU data list
Item No.Item nameNormal condition
51IG1-2 Fuel pump relayOFF
ETACS-ECU data list
Item No.Item nameNormal condition
51IG1-2 Fuel pump relayOFF
  • When power supply mode is "ON."
 
ETACS-ECU data list
Item No.Item nameNormal condition
51IG1-2 Fuel pump relayOFF
ETACS-ECU data list
Item No.Item nameNormal condition
51IG1-2 Fuel pump relayOFF
OK: Normal conditions are displayed for the items.
Are the check result normal?
: Go to Step 6.
Go to Step 7.
 
STEP 6. Check whether the DTC is set again.
Check again if the DTC is set in the KOS&OSS-ECU.
(1) Erase the DTC.
(2) Turn the power supply mode of the engine switch from "OFF" to "ON."
(3) On completion, check that the DTC is set again.
Is the DTC set?
Replace the ETACS-ECU (Refer to GROUP 54A - ETACS - ETACS-ECU ).
Intermittent malfunction is suspected (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
 
STEP 7. Check whether the DTC is set again.
Check again if the DTC is set in the KOS&OSS-ECU.
(1) Erase the DTC.
(2) Turn the power supply mode of the engine switch from "OFF" to "ON."
(3) On completion, check that the DTC is not set again.
Is the DTC set?
Replace the KOS&OSS-ECU and register the ID codes (Refer to ).
Intermittent malfunction is suspected (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).