[Previous][Next]
DTC C1707: Implausible Coding Data
 
 
caution
  • If there is any problem in the CAN bus lines, an incorrect DTC may be set. Prior to this diagnosis, diagnose the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ).
  • Whenever ECU is replaced, ensure that the CAN bus lines are normal.
  • When DTC C1707 is set in ASC-ECU, the DTC may also be set in ETACS-ECU. When the DTC is set in ETACS-ECU, carry out the diagnosis of the DTC for ETACS-ECU first.
 
 
OPERATION
ASC-ECU receives the vehicle information stored in the ETACS-ECU via CAN bus lines.
 
 
 
DTC SET CONDITIONS
When received invalid coding data from the ETACS-ECU, this DTC is set.
 
 
 
PROBABLE CAUSES
  • Malfunction of ETACS-ECU
  • ETACS-ECUs have been interchanged between two vehicles.
  • ASC-ECU malfunction
  • ASC-ECUs have been interchanged between two vehicles.
  • Malfunction of ETACS-ECU coding data
  • ECM malfunction
 
 
 
 
DIAGNOSIS
STEP 1. Using scan tool (M.U.T.-IIISE), diagnose the CAN bus line.
(1)
cautionTo prevent damage to scan tool (M.U.T.-IIISE), always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool (M.U.T.-IIISE).
Connect scan tool (M.U.T.-IIISE). Refer to "How to connect the Scan Tool (M.U.T.-IIISE) ."
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the check result normal?
Go to Step 3.
Repair the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ). On completion, go to Step 2.
 
STEP 2. DTC recheck after resetting CAN bus lines.
Is DTC C1707 set?
Go to Step 3.
This diagnosis is complete.
 
STEP 3. Using scan tool (M.U.T.-IIISE), check other system DTC.
Use scan tool (M.U.T.-IIISE) to check whether any coding-related DTC is set by ETACS-ECU or ECM.
Is the DTC set?
Troubleshoot for the relevant DTC.
Go to Step 4.
 
STEP 4. Check part number of ASC-ECU.
Check the part number of ASC-ECU.
Is the check result normal?
Go to Step 5.
Replace the hydraulic unit (integrated with ASC-ECU) (Refer to ).
 
STEP 5. ETACS-ECU coding data check.
Is the check result normal?
Go to Step 6.
Replace the ETACS-ECU (Refer to GROUP 54A - ETACS-ECU ).
 
STEP 6. Check part number of ETACS-ECU.
Check the part number of ETACS-ECU.
Is the check result normal?
Go to Step 7.
Replace the ETACS-ECU (Refer to GROUP 54A - ETACS-ECU ).
 
STEP 7. ECM coding data check.
Is the check result normal?
Go to Step 8.
Replace the ECM (Refer to GROUP 13A - ECM ).
 
STEP 8. Check whether the DTC is set again.
Erase the DTC.
Is DTC C1707 set?
Replace the hydraulic unit (integrated with ASC-ECU) (Refer to ).
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/How to Cope with Intermittent Malfunctions ).