[Previous][Next]
Inspection Procedure 1: Power supply circuit check
Inspection Procedure 2: The odometer and the trip meter are not displayed.
Inspection Procedure 3: No needle meters work.
Inspection Procedure 4: If the ignition switch is turned to the "ON" position, the indicator and warning lights do not illuminate normally.
 
 
 
 
TECHNICAL DESCRIPTION (COMMENT)
If the odometer and trip meter is not displayed or no needle meters work, power supply to the combination meter, or the combination meter itself may have a problem.
 
 
 
TROUBLESHOOTING HINTS
  • The wiring harness or connectors may have loose, corroded, or damaged terminals, or terminals pushed back in the connector.
  • The combination meter may be defective.
 
 
 
DIAGNOSIS
Required Special Tools:
  • MB991223: Harness Set
  • MB992006: Extra Fine Probe
STEP 1. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code.
Check if DTC is set in the combination meter.
(1)
cautionTo prevent damage to scan tool (M.U.T.-III), always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool (M.U.T.-III).
Connect scan tool (M.U.T.-III). Refer to "How to connect the Scan Tool (M.U.T.-III) ."
(2) Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
(3) Check if DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the DTC set?
Troubleshoot the combination meter (Refer to ).
Go to Step 2.
 
STEP 2. Voltage measurement at the combination meter connector.
(1) Disconnect the connector, and measure at the wiring harness side.
(2) Turn the ignition switch to the "LOCK" (OFF) position.
(3) Measure the voltage between the combination meter connector (B+B terminal) and ground.
OK: The voltage should measure approximately 12 volts (battery positive voltage).
Is the check result normal?
Go to Step 4.
Go to Step 3.
 
STEP 3. Check of open circuit in B+B line between the fusible link and combination meter connector.
Is the check result normal?
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ).
Repair the connector(s) or wiring harness.
 
STEP 4. Voltage measurement at the combination meter connector.
(1) Disconnect the connector, and measure at the wiring harness side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between the combination meter connector (IG1 terminal) and ground.
OK: The voltage should measure approximately 12 volts (battery positive voltage).
Is the check result normal?
Go to Step 7.
Go to Step 5.
 
STEP 5. Using scan tool (M.U.T.-III), check data list.
Check the input signal from the ignition switch (IG1) in the ETACS-ECU.
  • Turn the ignition switch to the "ON" position.
 
Item No.Item nameNormal condition
30Ignition switch (IG1)ON
OK: Normal condition is displayed.
Is the check result normal?
Go to Step 6.
Troubleshoot the ETACS-ECU. Refer to Inspection Procedure 2 "The ignition switch (IG1) signal is not received." .
 
STEP 6. Check of open circuit in IG1 line between the ignition switch (IG1) and combination meter connector.
Is the check result normal?
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).
Repair the connector(s) or wiring harness.
 
STEP 7. Resistance measurement at the combination meter connector.
(1) Disconnect the connector, and measure at the wiring harness side.
(2) Measure the resistance between the combination meter connector (GND terminal) and ground.
OK: The resistance should be 2 ohm or less.
Is the check result normal?
Go to Step 9.
Go to Step 8.
 
STEP 8. Check of open circuit in GND line between combination meter connector and ground.
Is the check result normal?
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).
Repair the connector(s) or wiring harness.
 
STEP 9. Retest the system.
Is the check result normal?
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).
Replace the combination meter.