[Previous][Next]
DTC B1428: Side impact sensor (front: RH) communication error
DTC B1429: Side impact sensor (front: RH) communication impossible
 
 
cautionIf DTC B1428 or B1429 is stored in the SRS-ECU, always diagnose the CAN main bus line.
 
 
CIRCUIT OPERATION
If an impact of set value or more is detected, the side impact sensor (front: RH) sends the coded acceleration data to SRS-ECU. Based on the acceleration data, SRS-ECU determines the necessity of side-airbag and curtain air bag deployment, and then turns ON the power supply circuit to the inflator.
 
 
DTC SET CONDITIONS
The diagnostic trouble code is stored if the communication between the side impact sensor (front: RH) and SRS-ECU is abnormal (No. B1428), or impossible (No. B1429).
 
 
TROUBLESHOOTING HINTS
  • Malfunction of the side impact sensor (front: RH)
  • Damaged wiring harness and connectors
  • Malfunction of SRS-ECU
 
 
DIAGNOSIS
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.
(1)
cautionTo prevent damage to scan tool (M.U.T.-III), always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool (M.U.T.-III).
Connect scan tool (M.U.T.-III). Refer to "How to connect the scan tool ."
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the CAN bus line found to be normal?
Go to Step 2.
Repair the CAN bus line (Refer to GROUP 54C, Diagnosis ).
 
STEP 2. Recheck for diagnostic trouble code.
Check again if the DTC is stored.
(1) Erase the DTC.
(2) Turn the ignition switch to the "ON" position.
(3) Check if the DTC is stored.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the DTC stored?
Go to Step 3.
There is an intermittent malfunction such as poor engaged connector(s) or open circuit (Refer to GROUP 00, How to Cope with Intermittent Malfunction ).
 
STEP 3. Check the side impact sensor (front: RH).
(1) Check that the negative battery terminal is disconnected. If the negative battery terminal is connected, disconnect it.
(2) Alternate the side impact sensor (front: RH) and the side impact sensor (front: LH), and then install the alternated sensors.
(3) Connect the negative battery terminal.
(4) After erasing the DTC memory, check the DTC again.
(5) Disconnect the negative battery terminal.
Is DTC B1428 or B1429 stored?
Replace the side impact sensor (front: RH) with a new one (Refer to ).
Go to Step 4.
 
STEP 4. Check of short to power supply, short to ground, and open circuit in SSR-, SSR+ line in between SRS-ECU connector and side impact sensor (front: RH) connector.
Is the check result normal?
Go to Step 5.
Repair the connectors or harness wires.
 
STEP 5. Check whether the DTC is stored again.
Check again if the DTC is stored.
(1) Erase the DTC.
(2) Turn the ignition switch to the "ON" position.
(3) Check if the DTC is stored.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is DTC B1428 or B1429 stored?
Replace SRS-ECU (Refer to ).
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).