[Previous][Next]
DTC P0138: Heated Oxygen Sensor (rear) Circuit High Voltage
 
 
 
 
CIRCUIT OPERATION
  • A voltage corresponding to the oxygen concentration in the exhaust gas is sent to the ECM terminal O2RL from the output terminal of the heated oxygen sensor (rear).
  • Ground terminal of the heated oxygen sensor (rear) is grounded with ECM terminal ORLE.
  • The ECM applies an offset voltage of 0.5 volt to ground terminal of the heated oxygen sensor (rear).
 
 
TECHNICAL DESCRIPTION
  • The output signal of the linear air-fuel ratio sensor is compensated by the output signal of the heated oxygen sensor (rear).
  • The ECM checks for the heated oxygen sensor (rear) output voltage.
 
 
DESCRIPTIONS OF MONITOR METHODS
  • Heated oxygen sensor (rear) output voltage is over specified range.
 
 
MONITOR EXECUTION
  • Continuous
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
  • Linear air-fuel ratio sensor monitor
  • Linear air-fuel ratio sensor heater monitor
  • Heated oxygen sensor heater (rear) monitor
  • Heated oxygen sensor offset voltage monitor
Sensor (The sensor below is determined to be normal)
  • Mass airflow sensor
  • Engine coolant temperature sensor
  • Intake air temperature sensor
  • Barometric pressure sensor
 
 
DTC SET CONDITIONS
Logic Flow Chart
 
 
Check Conditions
  • More than 2 seconds have passed since the engine starting sequence was completed.
  • Heated oxygen sensor offset voltage is between 0.4 and 0.6 volt.
Judgment Criterion
  • Heated oxygen sensor (rear) output voltage is more than 1.8 volts for 2 seconds.
 
 
FAIL-SAFE AND BACKUP FUNCTION
  • None
 
 
OBD-II DRIVE CYCLE PATTERN
  • Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 22 .
 
 
TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
  • Short circuit in heated oxygen sensor (rear) output line.
  • Connector damage.
  • ECM failed.

 
 
DIAGNOSIS
Required Special Tools:
  • MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
  • MB992745: V.C.I.-Lite main harness A
  • MB992747: V.C.I.-Lite USB cable short
  • MB992748: V.C.I.-Lite USB cable long
  • MB991958: Scan Tool (M.U.T.-III Sub Assembly)
    • MB991824: Vehicles Communication Interface (V.C.I.)
    • MB991827: M.U.T.-III USB Cable
    • MB991910: M.U.T.-III Main Harness A (Vehicles with CAN communication system)
  • MB991658: Test Harness
STEP 1. Using scan tool (M.U.T.-III), check data list item AD: Heated Oxygen Sensor (rear).
cautionTo prevent damage to scan tool (M.U.T.-III), always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool (M.U.T.-III).
(1) Connect scan tool (M.U.T.-III). Refer to HOW TO CONNECT THE SCAN TOOL (M.U.T.-III) .
(2) Start the engine and run at idle.
(3) Set scan tool (M.U.T.-III) to the data reading mode for item AD, Heated Oxygen Sensor (rear).
  1. Transaxle: 2nd (CVT: L range) speed
  2. Drive with wide open throttle
  3. Engine: 3,500 r/min or more
    • The output voltages should be between 0.6 and 1.0 volt.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the sensor operating properly?
It can be assumed that this malfunction is intermittent. Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions .
Go to Step 2.
 
STEP 2. Check of short circuit to power supply in O2RL line between heated oxygen sensor (rear) connector and ECM connector.
Is the harness wire in good condition?
Go to Step 3.
Repair the connector(s) or wiring harness. Then go to Step 4.
 
STEP 3. Using scan tool (M.U.T.-III), check data list item AD: Heated Oxygen Sensor (rear).
(1) Start the engine and run at idle.
(2) Set scan tool (M.U.T.-III) to the data reading mode for item AD, Heated Oxygen Sensor (rear).
  1. Transaxle: 2nd speed (CVT: L range)
  2. Drive with wide open throttle
  3. Engine: 3,500 r/min or more
    • The output voltages should be between 0.6 and 1.0 volt.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Is the sensor operating properly?
It can be assumed that this malfunction is intermittent. Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions .
Replace the ECM (Refer to Removal and Installation ). Then go to Step 4.
 
STEP 4. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 22 .
(2) Check the diagnostic trouble code (DTC).
Is DTC P0138 set?
Retry the troubleshooting.
The inspection is complete.