00-CODING LIST

CODING LIST

caution

With the ETACS functions being customized, if any of the ETACS-ECU variant coding and option coding items are changed, the customized contents are reset. In such case, the functions need to be recustomized.

Before troubleshooting, check that the coding data written into the engine control module (ECM), SRS-ECU and ETACS-ECU are normal. If they are not the same as the initial settings, various functions and systems do not work normally.

VARIANT CODING

Required Special Tools:

MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
MB992745: V.C.I.-Lite main harness A
MB992747: V.C.I.-Lite USB cable short
MB992748: V.C.I.-Lite USB cable long
MB991958: Scan Tool (M.U.T.-III Sub Assembly)

MB991824: Vehicles Communication Interface (V.C.I.)
MB991827: M.U.T.-III USB Cable
MB991910: M.U.T.-III Main Harness A (Vehicles with CAN communication system)

The coding data can be checked by operating scan tool (M.U.T.-III).

note	For details on how to use the scan tool (M.U.T.-III), refer to the "M.U.T.-III Owner’s manual".

caution

To prevent damage to scan tool (M.U.T.-III), always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool (M.U.T.-III).

1. Ensure that the ignition switch is at the "LOCK" (OFF) position.

2. Start up the personal computer.

3. Connect special tool MB992747/M992748 or special tool MB991827 to special tool MB992744 or special tool MB991824 and the personal computer.

4. Connect special tool MB992745 or special tool MB991910 to special tool MB992744 or special tool MB991824.

5. Connect special tool MB992745 or special tool MB991910 to the data link connector.

note	When the special tool MB992745 is connected to the data link connector, the special tool MB992744 indicator light will be illuminated in a green color.

6. Turn the power switch of special tool MB991824 to the "ON" position. <When using the special tool MB991824>

note	When special tool MB991824 is energized, special tool MB991824 indicator light will be illuminated in a green color.

7. Start the M.U.T.-III system on the personal computer and turn the ignition switch to the "ON" position.

8. On the system selection screen, select "MFI" to check the engine control module data, "SRS-AIR BAG" to check the SRS-ECU data, and "ETACS" to check the ETACS-ECU data.

9. Select "Coding".

10. Select "Coding Information & Copy".

11. If the displayed coding information is different from the corresponding initial setting in the list, replace the ECU with a correctly coded one. For replacement of the engine control module, refer to GROUP 13A, Engine Control Module

. For replacement of the SRS-ECU, refer to GROUP 52B, SRS Control Unit

. For replacement of the ETACS-ECU, refer to GROUP 54A, ETACS

ENGINE CONTROL MODULE CODING DATA LIST

note	The items to be displayed may differ depending on the version of the scan tool (M.U.T.-III).

Item name	Initial value
Vehicle Model	MIRAGE G4
Model year	(Displays the model year)
Destination	U.S.
Engine type	3A92 1.2L
Final drive	2WD
Model year half	0
Final gear ratio	4.055(MT)
Final gear ratio	3.757(CVT)
Tire circumference	1748mm
IMMOBILIZER	Not present or Present
ABS	Not present
A.S.C.	Present
EPS	Present
ECO indicator	Present
A/C	Not present or Present
Power window Dr	Not present
Power window As	Not present
Power window RR	Not present
Power window RL	Not present
OSS	Not present or Present
Cruise control	Not present or Present
Cruise control option coding	Not accept
Compressor type	No compressor or Type 1
FCM	Not present
S/W variation	No. 1

SRS-ECU CODING DATA LIST

note	The items to be displayed may differ depending on the version of the scan tool (M.U.T.-III).

Item name	Initial value
DR airbag squib(1st)	Present
PS airbag squib(1st)	Present
DR airbag squib(2nd)	Present
DR pretensioner squib	Present
PS pretensioner squib	Present
DR lap pretensioner squib	Not present
PS lap pretensioner squib	Not present
RH side airbag squib	Present
LH side airbag squib	Present
RH curtain airbag squib	Present
LH curtain airbag squib	Present
DR knee airbag squib	Present
2nd seat (RH) pretensioner squib	Not present
2nd seat (LH) pretensioner squib	Not present
Front impact SNSR equipment type	Both sides
RH side sensor B-pillar	Present
LH side sensor B-pillar	Present
DR seat position sensor	Not present
PS cut off SW	Not present
Passenger’s SRS OFF indicator	Present
Passenger’s SRS ON indicator	Present
High volt.cutoff communication	Not present
Emergency call communication	Not present
Crash parameter flag(#0)	ON
Crash parameter flag(#1)	OFF
Crash parameter flag(#2)	OFF
Crash parameter flag(#3)	OFF
Crash parameter flag(#4)	OFF
Crash parameter flag(#5)	OFF
Crash parameter flag(#6)	OFF
Crash parameter flag(#7)	OFF
High volt.cutoff para.flag(#0)	OFF
High volt.cutoff para.flag(#1)	OFF
High volt.cutoff para.flag(#2)	OFF
High volt.cutoff para.flag(#3)	OFF
High volt.cutoff para.flag(#4)	OFF
High volt.cutoff para.flag(#5)	OFF
High volt.cutoff para.flag(#6)	OFF
High volt.cutoff para.flag(#7)	OFF

ETACS-ECU CODING DATA LIST

note	The items to be displayed may differ depending on the version of the scan tool (M.U.T.-III).

Item name	Initial value
Compressor type*	No compressor or Type 1
Temperature type	Celsius or Fahrenheit
Average speed	Not available
Fuel consumption scale	L/100km or MPG (US)
Seat belt reminder logic	Except EU
Coolant temp gauge threshold	Normal
Frost warning threshold	U.S.
Distance to empty	Available
Average fuel consumption	Available
Instant fuel consumption	Not available
Trip autoreset IG OFF	Available
Seat belt reminder control type	AABT
Seat belt reminder indicator	D&P independent
Reverse alarm	Not available
Key reminder	Not available or Available
GCC speed alarm	Not available
Rent-a-car mode IG-OFF always	Available
Service reminder schedule table	Normal
Launch gear block alarm	Not present
TCM	Not present or Present
EPS	Present
EV	Not present
A/C	Not present or Present
OCM	Present
ORC	Present
WCM	Not present
ACC/FCM	Not present
OSS	Not present or Present
Model year	(Displays the model year)
Vehicle line	MIRAGE G4
Destination	U.S.
EPS type	Type 2
Immobilizer	Type A or Type B
Handle side	LHD
ABS	Not present
A.S.C.	Present
TPMS information	N/A or 32 psi or 35 psi
TPMS	Not present or Present(NAS)
TPMS Off mode function	Not present
Keyless entry*	Not present or Present
Vehicle Type for A.S.C.	Type 7 or Type 8
Brake Type for A.S.C.	Type 2
HBA Type	Type 1
ABS Type	Not present
TCL Type	Not present
A.S.C. Type	Not present
HSA Type	Type 1
AS&G brake hold Type	Not present
FCM type for A.S.C.	Not present
Tire circumference	1748 mm
A/C control type	Normal or NAS
Engine type	3A92 1.2L
Engine power	Normal
Transmission	5MT or CVT
F.A.S.T.	Not present or Type C
F.A.S.T. door entry type	Switch
Idle neutral control	Not present or Present
G sensor for CVT	Not present
T/M oil cooler	Not present
Transmission control type	Default
Model year half	0
GSI system	Not present
ESL	Default or Not present
F.A.S.T. SW type(Gate/trunk)	Trunk
Engine Type for OSS	Gasoline
F.A.S.T. LF output	Type 4
Transmission Type for OSS	Type 1
Option Heater	Not present
Fuel Tank Type	Type 2
Service reminder for month	6 month
Service reminder for km	12000 km
Service reminder for mile	7500 mile
GCC speed alarm indicator	Not present
AS&G status	Not present
ECO gauge	Not present
Gate/Trunk	Trunk type
Outside temperature	Not present or Present
Remote engine starter*	NotPresent/ChgNg or Present/Chg Ok
Comfort flasher type	Present/Chg Ok
Rear wiper by reverse customize	Disable or Enable
Dead lock operation customize	Disable
ACC power auto cut	Default disable
Room light auto cut by door	Enable
Horn chirp by keyless	Present/Chg Ok
Room light delay timer	Long
Room light by H/L	Full
Outer Buzzer Volume customize	Disable or Enable
Panic Alarm*	Disable or Enable
Multi mode RKE	D-spec
key reminder unlock	Disable or B-spec/Dr and As
Theft alarm mode	Disable
Theft alarm function	NotPresent/ChgNg
Pre-alarm	Not present
Manner Switch*	NotPresent/ChgNg
RLS Outside temperature control	Enable
RLS Outside temp. control type	A-spec
DRL signal	B-spec
Auto light control*	No/Chg Ng
Auto light control mode	High threshold
Wiper by washer	Disable
LED H/L indicator	Disable
Rear defogger timer	Enable
Power window mode	Type P3 or Type 5(NAFTA)
Power window Dr	Not present
Power window As	Not present
Power window RR	Not present
Power window RL	Not present
RLS*	Not present
RLS overwipe type	Type 4
RLS WS type	Type 2 (Green)
Shift lock	Not present or Present
DRL type	DRL not present or Dimming DRL w/ P
Vehicle type for ETACS Function	Type A
DRL function*	Present/Chg Ng or NotPresent/ChgNg
Headlight	2 beams
Headlight washer	Disable
Headlight auto cut	C-spec
Turn signal bulb	27W+21W+5W
Front fog light mode	Type B
Front fog light*	Not present or Present
Rear fog light*	NotPresent/ChgOk
Rear wiper	Disable
Wiper washer check bulb*	Present
Horn type*	Single horn
Door lock system	Not present or A-spec
ESS by turn light	Not present
ESS Cancel Function*	Not present
Fold mirror	Disable
Trunk opener mode	Not present or Present
ACC automatic cut customize(OSS)	Disable or Enable
Horn type select	Answer back ope.
Answer back operation time*	30 msec
RLS communication type	LIN
Coming home light customize	Disable
Welcome light customize	Disable

note	^*: The setting can be changed by the option coding. Refer to .

OPTION CODING

caution

If there is any item indicated by the option coding after equipment change, set ETACS-ECU so that the option coding data corresponds with the equipment content. Pay attention to that the concerned functions and systems do not work normally if the setting does not correspond with the equipment.
With the ETACS functions being customized, if any of the ETACS-ECU option coding items are changed, the customized contents are reset. In such case, the functions need to be recustomized.

The ETACS-ECU option coding data can be checked or changed by operating scan tool (M.U.T.-III).

How to check option coding data

Connect the scan tool (M.U.T.-III). Refer to .
Select "ETACS" on the system selection screen.
Select "Coding".
Select "Option Coding Information".
Check the displayed option coding information.

How to change option coding data

Connect the scan tool (M.U.T.-III) Refer to .
Select "ETACS" on the system selection screen.
Select "Coding".
Select "Option Coding".
Change to correct option coding data.

LIST

Item name
Auto light control
Keyless entry
RLS
Compressor type
Front fog light
Rear fog light
Manner Switch
Remote engine starter
DRL function
Wiper washer check valve
ESS Cancel Function
Panic Alarm
Answer back operation time