[Previous][Next]
DTC P2097: Post Catalyst Fuel Trim System too Rich (bank 1)
 
 
 
 
TECHNICAL DESCRIPTION
  • The ECM effects right bank air/fuel ratio feedback control in accordance with the signals from the linear air-fuel ratio sensor.
  • If the right bank linear air-fuel ratio sensor has deteriorated, corrections will be made by the right bank heated oxygen sensor (rear).
 
 
DESCRIPTIONS OF MONITOR METHODS
  • When an abnormality exists in the linear air-fuel ratio sensor, the amount of compensated fuel injection is abnormal. When this situation continues, it is judged to be faulty.
  • If an abnormality exists in the right bank heated oxygen sensor (rear), also it is judged to be faulty even though the right bank linear air-fuel ratio sensor is normal.
 
 
MONITOR EXECUTION
  • Continuous
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
  • Linear air-fuel ratio sensor monitor
  • Heated oxygen sensor (rear) monitor
  • Linear air-fuel ratio sensor heater monitor
  • Heated oxygen sensor (rear) heater monitor
  • Heated oxygen sensor offset voltage monitor
  • Misfire monitor
  • Fuel system monitor
Sensor (The sensor below is determined to be normal)
  • Mass airflow sensor
  • Engine coolant temperature sensor
  • Intake air temperature sensor
  • Barometric pressure sensor
  • Throttle position sensor
  • Accelerator pedal position sensor
 
 
DTC SET CONDITIONS
Logic Flow Chart
 
 
Check Conditions
  • Engine coolant temperature is more than 76°C (169°F).
  • The closed loop air/fuel control continues for more than 15 seconds.
  • More than 128 seconds have passed since the engine starting sequence was completed.
  • Mass airflow sensor output is more than 8 g/sec.
  • After the engine start, the accumulated time where the four conditions mentioned above are satisfied is more than 60 seconds.
Judgment Criterion
  • The amount of compensated lean air/fuel ratio is output by the right bank heated oxygen sensor (rear). The status that the amount of compensated lean air/fuel ratio is greater than the specified amount continues for 5 seconds.
 
 
FAIL-SAFE AND BACKUP FUNCTION
  • None
 
 
OBD-II DRIVE CYCLE PATTERN
  • Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 1 .
 
 
TROUBLESHOOTING HINTS (The most likely causes for this code to be stored are:)
  • Right bank linear air-fuel ratio sensor failed.
  • Right bank heated oxygen sensor (rear) failed.
  • Injector failed.
  • ECM failed.

 
 
DIAGNOSIS
Required Special Tools:
  • MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
  • MB992745: V.C.I.-Lite main harness A
  • MB992747: V.C.I.-Lite USB cable short
  • MB992748: V.C.I.-Lite USB cable long
  • MB991958: Scan Tool (M.U.T.-III Sub Assembly)
    • MB991824: Vehicles Communication Interface (V.C.I.)
    • MB991827: M.U.T.-III USB Cable
    • MB991910: M.U.T.-III Main Harness A (Vehicles with CAN communication system)
STEP 1. Using scan tool (M.U.T.-III), read the diagnostic trouble code (DTC).
cautionTo prevent damage to scan tool (M.U.T.-III), always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool (M.U.T.-III).
(1) Connect scan tool (M.U.T-III). Refer to HOW TO CONNECT THE SCAN TOOL (M.U.T.-III) .
(2) Turn the ignition switch to the "ON" position.
(3) Read the DTC.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the diagnostic trouble code other than P2096 stored?
Refer to Diagnostic Trouble Code Chart .
Go to Step 2.
 
STEP 2. Replace the right bank linear air-fuel ratio sensor.
(1) Replace the right bank linear air-fuel ratio sensor.
(2) Carry out a test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 1 .
(3) Check the diagnostic trouble code (DTC).
Is DTC P2097 stored?
Go to Step 3.
The inspection is complete.
 
STEP 3. Replace the right bank heated oxygen sensor (rear).
(1) Replace the right bank heated oxygen sensor (rear).
(2) Carry out a test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 1 .
(3) Check the diagnostic trouble code (DTC).
Is DTC P2097 stored?
Go to Step 4.
The inspection is complete.
 
STEP 4. Replace the right bank injector.
(1) Replace the right bank injector.
(2) Carry out a test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 1 .
(3) Check the diagnostic trouble code (DTC).
Is DTC P2097 stored?
Replace the ECM (Refer to Removal and Installation ).
The inspection is complete.