[Previous][Next]
Diagnosis Procedure
1.ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR
With M.U.T.-III SE
Perform neutral position adjustment of steering angle sensor. Refer to Work Procedure.
: .
 
2.PERFORM DIAGNOSTIC TROUBLE CODE (1)
With M.U.T.-III SE
  1. Electric motor switch OFF (Auto ACC function OFF).
  2. Electric motor switch ON.
    noteWait at least 10 seconds after electric motor switch ON.
  3. Perform Diagnostic Trouble Code for “ABS".
Is DTC “C106E-64" detected?
“Active DTC" is displayed: .
“Stored DTC" is displayed: INSPECTION END (Erase the memory of Diagnostic Trouble Code results.)
INSPECTION END
 
3.CHECK CONNECTOR
  1. Disconnect 12V battery negative terminal.
  2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
  3. Check the steering angle sensor harness connector for disconnection or looseness.
Is the inspection result normal?
.
Repair / replace harness or connector, securely lock the connector. .
 
4.PERFORM DIAGNOSTIC TROUBLE CODE (2)
With M.U.T.-III SE
  1. Connect 12V battery negative terminal.
  2. Electric motor switch ON.
    noteWait at least 10 seconds after electric motor switch ON.
  3. Perform Diagnostic Trouble Code for “ABS".
Is DTC “C106E-64" detected?
“Active DTC" is displayed: .
“Stored DTC" is displayed: INSPECTION END (Erase the memory of Diagnostic Trouble Code results.)
INSPECTION END
 
5.STEERING ANGLE SENSOR POWER SUPPLY
  1. Disconnect 12V battery negative terminal.
  2. Disconnect steering angle sensor harness connector.
  3. Connect 12V battery negative terminal.
  4. Check the voltage between steering angle sensor harness connector and ground.
    +―Voltage
    Steering angle sensor
    ConnectorTerminal
    M568GroundApprox. 0 V
  5. Electric motor switch ON.
    noteElectric motor switch ON.
  6. Check the voltage between steering angle sensor harness connector and ground.
    +―Voltage
    Steering angle sensor
    ConnectorTerminal
    M568Ground10 - 16 V
Is the inspection result normal?
.
.
 
6.STEERING ANGLE SENSOR POWER SUPPLY CIRCUIT
  1. Disconnect 12V battery negative terminal.
  2. Check the 5A fuse (#5).
  3. Disconnect fuse block (J/B) harness connector.
  4. Check the continuity between steering angle sensor harness connector and fuse block (J/B) harness connector.
    Steering angle sensorFuse block (J/B)Continuity
    ConnectorTerminalConnectorTerminal
    M568M686FExisted
  5. Check the continuity between steering angle sensor harness connector and ground.
    Steering angle sensor—Continuity
    ConnectorTerminal
    M568GroundNot Existed
Perform trouble diagnosis for ignition power supply.
Repair / replace harness, connector, or fuse.
 
7.STEERING ANGLE SENSOR GROUND CIRCUIT
Check the continuity between steering angle sensor harness connector and ground.
Steering angle sensor—Continuity
ConnectorTerminal
M565GroundExisted
Is the inspection result normal?
.
Repair / replace harness or connector.
 
8.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
.
Repair / replace harness, connector, terminal, fuse, or fusible link.
 
9.CHECK TERMINAL
  1. Disconnect 12V battery negative terminal.
  2. Check the steering angle sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
.
Repair / replace harness, connector, or terminal.
 
10.CHECK CAN COMMUNICATION LINE
  1. Connect steering angle sensor harness connector.
  2. Connect fuse block (J/B) harness connector.
  3. Connect 12V battery negative terminal.
  4. Check the CAN communication line. Refer to Trouble Diagnosis Flow Chart.
Is the inspection result normal?
.
Repair / replace harness or connector.
 
11.CHECK DATA MONITOR
With M.U.T.-III SE
  1. Select "ABS", "Data List" and "Steering angle" according to this order.
  2. Check that the indication changes with steering angle when the steering wheel is turned left/right from the neutral position. Refer to Reference Value.
Is the inspection result normal?
Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
Replace the steering angle sensor. Refer to Removal and Installation.