[Previous][Next]
Diagnosis Procedure
cautionNever check between wheel sensor harness connector terminals.
1.CHECK WHEEL SENSOR
  1. Disconnect 12V battery negative terminal.
  2. Check the front right wheel sensor for damage.
Is the inspection result normal?
.
.
 
2.REPLACE WHEEL SENSOR (1)
With M.U.T.-III SE
  1. Replace the front right wheel sensor. Refer to Removal and Installation.
  2. Connect 12V battery negative terminal.
  3. Erase Diagnostic Trouble Code result for “ABS".
  4. Electric motor switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).
  5. Electric motor switch ON.
    noteWait at least 10 seconds after electric motor switch ON.
  6. Perform Diagnostic Trouble Code for “ABS".
Is DTC “C1603-12" detected?
.
INSPECTION END
 
3.CHECK CONNECTOR
  1. Disconnect 12V battery negative terminal.
  2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
  3. Check the front right wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
.
Repair / replace harness or connector, securely lock the connector. .
 
4.PERFORM DIAGNOSTIC TROUBLE CODE (1)
With M.U.T.-III SE
  1. Connect 12V battery negative terminal.
  2. Erase Diagnostic Trouble Code result for “ABS".
  3. Electric motor switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).
  4. Electric motor switch ON.
    noteWait at least 10 seconds after electric motor switch ON.
  5. Perform Diagnostic Trouble Code for “ABS".
Is DTC “C1603-12" detected?
.
INSPECTION END
 
5.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
.
Repair / replace harness, connector, terminal, fuse, or fusible link.
 
6.CHECK TERMINAL
  1. Disconnect 12V battery negative terminal.
  2. Disconnect ABS actuator and electric unit (control unit) harness connector and then check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.
  3. Disconnect front right wheel sensor harness connector and check the front right wheel sensor terminals for damage or loose connection with harness connector.
Is the inspection result normal?
.
Repair / replace harness, connector, or terminal. .
 
7.PERFORM DIAGNOSTIC TROUBLE CODE (2)
With M.U.T.-III SE
  1. Connect ABS actuator and electric unit (control unit) harness connector.
  2. Connect front right wheel sensor harness connector.
  3. Connect 12V battery negative terminal.
  4. Erase Diagnostic Trouble Code result for “ABS".
  5. Electric motor switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).
  6. Electric motor switch ON.
    noteWait at least 10 seconds after electric motor switch ON.
  7. Perform Diagnostic Trouble Code for “ABS".
Is DTC “C1603-12" detected?
.
INSPECTION END
 
8.CHECK WHEEL SENSOR HARNESS
  1. Disconnect 12V battery negative terminal.
  2. Disconnect ABS actuator and electric unit (control unit) harness connector.
  3. Disconnect front right wheel sensor harness connector.
  4. Check the continuity between ABS actuator and electric unit (control unit) harness connector and front right wheel sensor harness connector. (Check the continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)
    • Measurement connector and terminal for power supply circuit
      ABS actuator and electric unit (control unit)Front right wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      E12521E431Existed
    • Measurement connector and terminal for signal circuit
      ABS actuator and electric unit (control unit)Front right wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      E12526E432Existed
Is the inspection result normal?
.
Repair / replace harness or connector. .
 
9.PERFORM DIAGNOSTIC TROUBLE CODE (3)
With M.U.T.-III SE
  1. Connect ABS actuator and electric unit (control unit) harness connector.
  2. Connect front right wheel sensor harness connector.
  3. Connect 12V battery negative terminal.
  4. Erase Diagnostic Trouble Code result for “ABS".
  5. Electric motor switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).
  6. Electric motor switch ON.
    noteWait at least 10 seconds after electric motor switch ON.
  7. Perform Diagnostic Trouble Code for “ABS".
Is DTC “C1603-12" detected?
.
INSPECTION END
 
10.REPLACE WHEEL SENSOR
With M.U.T.-III SE
  1. Replace the front right wheel sensor. Refer to Removal and Installation.
  2. Connect ABS actuator and electric unit (control unit) harness connector.
  3. Connect 12V battery negative terminal.
  4. Erase Diagnostic Trouble Code result for “ABS".
  5. Electric motor switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).
  6. Electric motor switch ON.
    noteWait at least 10 seconds after electric motor switch ON.
  7. Perform Diagnostic Trouble Code for “ABS".
Is DTC “C1603-12" detected?
Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
INSPECTION END