[Previous][Next]
DTC No. P0AC6-00 Temperature Sensor 2 Characteristic Diagnosis
 
 
 
 
MONITOR EXECUTION
Continuous
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC set in memory for the item monitored below)
  • BMU monitor
Sensor (The sensor below is determined to be normal)
  • Drive battery temperature sensor
 
 
DTC SET CONDITIONS
Logic Flow Chart
 
 
Check Condition
  • The BMU power supply voltage is more than 7.578 volts.
Judgment Criterion
  • While the value subtracting the sensor B temperature from the sensor A temperature is 30°C (86°F) or more, the value subtracting the sensor C temperature from the sensor B temperature is 30°C (86°F) or more for 5 seconds or more.
 
 
OBD-II DRIVE CYCLE PATTERN
 
 
TROUBLESHOOTING HINTS
  • Damaged wiring harness and connectors
  • Malfunction of the battery module temperature sensor No. 2
  • Malfunction of the BMU
 
 
DIAGNOSIS
Required Special Tools:
  • MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
  • MB992745: V.C.I.-Lite main harness A
  • MB992747: V.C.I.-Lite USB cable short
  • MB992748: V.C.I.-Lite USB cable long
  • MB991223: Wiring harness set
  • MB992006: Extra fine probe
1.Check of continuity at drive battery connector (control wiring harness connector) (Battery module temperature sensor No. 2 shield line)
(1) Disconnect the connector, and measure at the wiring harness side.
(2) Check the following for continuity.
  • Continuity between the drive battery connector (control wiring harness connector) (terminal No. 23) and body ground
OK: Continuity exists (2 Ω or less)
Is the check result normal?
Repair the connector(s) or wiring harness. Then,
 
2.Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to OBD-II Drive Cycle OBD-II DRIVE CYCLE.
(2) Check the DTC.
Is the DTC set?
The trouble can be an intermittent malfunction (Refer to General Information - How to Use Troubleshooting/Inspection Service Points, How to Cope with Intermittent Malfunctions HOW TO COPE WITH INTERMITTENT MALFUNCTIONS).
 
3.Drive battery control wiring harness check (Battery module temperature sensor No. 2 signal line)
(1) Disassemble the drive battery (Refer to SERVICE PROCEDURE).
(2) Check the following wiring harness for short to ground circuit and open circuit.
  • Between the battery module temperature sensor No. 2 connector (terminal No. 2) and BMU connector (terminal No. 36)
Is the check result normal?
Repair the connector(s) or wiring harness. Then,
 
4.Drive battery control wiring harness check (Battery module temperature sensor No. 2 ground line)
Check the following wiring harness for open circuit.
  • Between the battery module temperature sensor No. 2 connector (terminal No. 1) and BMU connector (terminal No. 32)
Is the check result normal?
Repair the connector(s) or wiring harness. Then,
 
5.Drive battery control wiring harness check (Battery module temperature sensor No. 2 shield line)
Check the following wiring harness for open circuit.
  • Between the battery module temperature sensor No. 2 connector (terminal No. 3) and drive battery connector (control wiring harness connector) (terminal No. 23)
Is the check result normal?
Repair the connector(s) or wiring harness. Then,
 
6.Battery module temperature sensor No. 2 check
Check the battery module temperature sensor No. 2 (Refer to BATTERY TEMPERATURE SENSOR CHECK).
Is the check result normal?
Replace the BMU (Refer to BATTERY MANAGEMENT UNIT (BMU) REMOVAL AND INSTALLATION). Then,
Replace the battery module temperature sensor No. 2 (Refer to SERVICE PROCEDURE). Then,
 
7.Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to OBD-II Drive Cycle OBD-II DRIVE CYCLE.
(2) Check the DTC.
Is the DTC set?
Retry the troubleshooting.
The procedure is complete.