[Previous][Next]
Inspection Procedure 13: ETACS-ECU does not receive any signal from the stoplight switch. <Vehicles without stop light relay>
 
 
 
 
COMMENTS ON TROUBLE SYMPTOM
The stoplight switch input signal is used for the operation judgment of the functions below. If the signal is abnormal, these functions will not work.
  • ASC
  • Shift lock mechanism
  • OSS
 
 
TROUBLESHOOTING HINTS
  • The stoplight switch may be defective
  • The ETACS-ECU may be defective
  • The wiring harness or connectors may have loose, corroded, or damaged terminals, or terminals pushed back in the connector
 
 
DIAGNOSIS
Required Special Tools:
  • MB991223: Harness Set
  • MB992006: Extra Fine Probe
STEP 1. Check the stoplight switch connector C-25, ETACS-ECU connectors C-403 and C-410 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Is stoplight switch connector C-25, ETACS-ECU connectors C-403 and C-410 in good condition?
Go to Step 2.
Repair or replace the damaged component(s). Refer to GROUP 00E, Harness Connector Inspection . Check that the input signal of stoplight switch is normal.
 
STEP 2. Check the stoplight switch.
Remove the stoplight switch. Then check the continuity between the switch terminals.
 
Check conditionTerminal connector of testerNormal condition
At free position1 - 2 (for stoplight switch)Continuity exists
(2 Ω or less)
3 - 4 (for cruise control)No continuity
Press the plunger from the edge of the outer case by the dimension shown in the figure.1 - 2 (for stoplight switch)No continuity
3 - 4 (for cruise control)Continuity exists
(2 Ω or less)
Is the liftgate latch switch in good condition?
Go to Step 3.
Replace the stoplight switch. Check that the input signal of stoplight switch is normal.
 
STEP 3. Check the battery power supply circuit to the stoplight switch. Measure the voltage at stoplight switch connectors C-25.
(1) Disconnect stoplight switch connectors C-25 measure the voltage available at the wiring harness side of the connector.
(2) Measure the voltage between stoplight switch connector C-25 (terminal 1) and ground.
  • The voltage should measure approximately 12 volts (battery positive voltage).
Is the measured voltage approximately 12 volts (battery positive voltage)?
Go to Step 5.
Go to Step 4.
 
STEP 4. Check the following wiring harness.
Check the wiring harness for open and short circuit between the following connectors:
  • Wiring harness from ETACS-ECU connector C-403 (terminal 1) to stoplight switch connector C-25 (terminal 1)
Are all the wiring harness wires in good condition?
No action is necessary and testing is complete.
The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary. Check that the input signal of stoplight switch is normal.
 
STEP 5. Measure the voltage at the ETACS-ECU connector C-410.
(1) Measure by backprobing without disconnecting the ETACS-ECU connector and stoplight switch connector.
(2) Disconnecting the stoplight switch connector C-25.
(3) Measure the voltage between the ETACS-ECU connector C-410 (terminal16) and the body ground.
OK:
  • When the brake pedal is released: Approximately 0 V - 5 V (pulse)
  • When the brake pedal is depressed: Approximately system voltage
Is the check result normal?
Go to Step 7.
Go to Step 6.
 
STEP 6. Check the wiring harness between ETACS-ECU connector C-410 (terminal 16) and stoplight switch connector C-25 (terminal 2).
  • Check the signal line for open circuit.
Is the check result normal?
Go to Step 7.
Replace the wiring harness.
 
STEP 7. Using scan tool MB991958, check data list.
Temporarily replace the stoplight switch, and then depress the brake pedal.
 
Item No.Item nameNormal condition
Item 290Stoplight switchON
OK: Normal condition is displayed.
Is the check result normal?
Replace the stoplight switch.
Replace the ETACS-ECU.