[Previous][Next]
DTC P2123: Accelerator Pedal Position Sensor (main) Circuit High Input

 
 
 
 
CIRCUIT OPERATION
  • A 5-volt power supply is applied on the accelerator pedal position sensor (main) power terminal (terminal No. 1) from the ECM (terminal No. 75).
  • A voltage that is according to the accelerator opening angle is sent to the ECM (terminal No. 74) from the accelerator pedal position sensor (main) output terminal (terminal No. 3).
  • The ground terminal (terminal No. 2) is grounded with ECM (terminal No. 76).
 
 
TECHNICAL DESCRIPTION
  • The accelerator pedal position sensor (main) outputs voltage which corresponds to the accelerator pedal depression.
  • The ECM checks whether the voltage is within a specified range.
 
 
DESCRIPTIONS OF MONITOR METHODS
  • Accelerator pedal position sensor (main) output voltage is out of specified range.
 
 
MONITOR EXECUTION
  • Continuous
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
  • Not applicable
Sensor (The sensor below is determined to be normal)
  • Not applicable
 
 
DTC SET CONDITIONS
Logic Flow Chart
 
 
Check Condition
  • Ignition switch is "ON" position.
Judgment Criterion
  • Accelerator pedal position sensor (main) output voltage is more than 4.8 volts for 0.3 second.
 
 
FAIL-SAFE AND BACKUP FUNCTION
  • Throttle opening degree is restricted.
  • Throttle opening degree position is in default position if accelerator pedal position sensor (sub) fails.
 
 
OBD-II DRIVE CYCLE PATTERN
  • None.
 
 
TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
  • Accelerator pedal position sensor failed.
  • Open accelerator pedal position sensor (main) circuit, harness damage or connector damage.
  • ECM failed.

 
 
DIAGNOSIS
Required Special Tool:
  • MB991958: Scan Tool (M.U.T.-III Sub Assembly)
    • MB991824: V.C.I.
    • MB991827: USB Cable
    • MB991910: Main Harness A
STEP 1. Using scan tool MB991958, check data list item 11: Accelerator Pedal Position Sensor (main).
cautionTo prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to the data reading mode for item 11, Accelerator Pedal Position Sensor (main).
  • Output voltage should be between 900 and 1,100 millivolts when foot is released from accelerator pedal.
  • Output voltage should be 4,000 millivolts or more when accelerator pedal is fully depressed.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the sensor operating properly?
It can be assumed that this malfunction is intermittent. Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions .
Go to Step 2.
 
STEP 2. Check harness connector C-23 at accelerator pedal position sensor for damage.
Is the harness connector in good condition?
Go to Step 3.
Repair or replace it. Refer to GROUP 00E, Harness Connector Inspection . Then go to Step 8.
 
STEP 3. Check the continuity at accelerator pedal position sensor harness side connector C-23.
(1) Disconnect the connector C-23 and measure at the harness side.
(2) Check for the continuity between terminal No. 2 and ground.
  • Continuity (2 ohms or less)
Does continuity exist?
Go to Step 7.
Go to Step 4.
 
STEP 4. Check harness connector B-27 at ECM for damage.
Is the harness connector in good condition?
Go to Step 5.
Repair or replace it. Refer to GROUP 00E, Harness Connector Inspection . Then go to Step 8.
 
STEP 5. Check for open circuit and harness damage between accelerator pedal position sensor connector C-23 (terminal No. 2) and ECM connector B-27 (terminal No. 76).
Is the harness wire in good condition?
Go to Step 6.
Repair it. Then go to Step 8.
 
STEP 6. Using scan tool MB991958, check data list item 11: Accelerator Pedal Position Sensor (main).
(1) Turn the ignition switch to the "ON" position.
(2) Set scan tool MB991958 to the data reading mode for item 11, Accelerator Pedal Position Sensor (main).
  • Output voltage should be between 900 and 1,100 millivolts when foot is released from accelerator pedal.
  • Output voltage should be 4,000 millivolts or more when accelerator pedal is fully depressed.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Is the sensor operating properly?
It can be assumed that this malfunction is intermittent. Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions .
Replace the ECM (Refer to, Removal and Installation ). Then go to Step 8.
 
STEP 7. Replace the accelerator pedal assembly.
(1) Replace the accelerator pedal assembly.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is DTC P2123 set?
Replace the ECM (Refer to, Removal and Installation ). Then go to Step 8.
The inspection is complete.
 
STEP 8. Using scan tool MB991958, read the diagnostic trouble code (DTC).
(1) Turn the ignition switch to the "ON" position.
(2) After the DTC has been deleted, read the DTC again.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Is DTC P2123 set?
Retry the troubleshooting.
The inspection is complete.