[Previous][Next]
DTC B1E1D +Battery Roomlight Overload or Short Circuit
 
 
cautionBefore replacing the ECU, ensure that the power supply circuit, the ground circuit and the communication circuit are normal.
 
 
TROUBLE JUDGMENT
If any of the following lights does not come on, the ETACS-ECU will set DTC No. B1E1D.
  • Front dome light
  • Rear dome light
  • Luggage compartment light
  • Vanity mirror light
 
 
TECHNICAL DESCRIPTION (COMMENT)
DTC No. B1E1D will be set if the ETACS-ECU detects a short between itself and each of the lights.
 
 
TROUBLESHOOTING HINTS
  • The front dome light bulb may be defective
  • The front dome light body may be defective
  • The rear dome light bulb may be defective
  • The rear dome light body may be defective
  • The luggage compartment light bulb may be defective
  • The luggage compartment light body may be defective
  • The vanity mirror light bulb may be defective
  • The sun visor may be defective
  • The wiring harness or connectors may have loose, corroded, or damaged terminals, or terminals pushed back in the connector
  • The ETACS-ECU may be defective
 
 
DIAGNOSIS
Required Special Tools:
  • MB991223: Harness Set
  • MB992006: Extra Fine Probe
STEP 1. Bulb check
Check that the following bulbs are installed correctly.
  • Front dome light bulb
  • Rear dome light bulb
  • Luggage compartment light bulb
  • Vanity mirror light bulb
Is the check result normal?
Go to Step 2.
Replace or reinstall a bulb of the front dome light, the rear dome light, the luggage compartment light or the vanity mirror light.
 
STEP 2. Check the following wiring harness.
Check the wiring harness for short circuit between the following connectors:
  • Check of short circuit in LP+1 line front dome light connector and ETACS-ECU connector.
  • Check of short circuit in LP+1 line rear dome light connector and ETACS-ECU connector.
  • Check of short circuit in LP+1 line luggage compartment light connector and ETACS-ECU connector.
  • Check of short circuit in LP+1 line vanity mirror light connector and ETACS-ECU connector.
Is the check result normal?
Go to Step 3.
Repair the connector(s) or wiring harness.
 
STEP 3. Check the following wiring harness.
Check the wiring harness for short to ground circuit between the following connectors:
  • Check of short circuit in ground line front dome light connector and body ground.
  • Check of short circuit in ground line rear dome light connector and body ground.
  • Check of short circuit in ground line luggage compartment light connector and body ground.
  • Check of short circuit in ground line vanity mirror light connector and body ground.
Is the check result normal?
Go to Step 4
Repair the connector(s) or wiring harness.
 
STEP 4. Using scan tool (M.U.T.-IIISE), Check whether the DTC is set again.
Check again if DTC No.B1E1D is set in the ETACS-ECU.
(1)
cautionTo prevent damage to scan tool (M.U.T.-IIISE), always turn off the power supply mode of the electric motor switch before connecting or disconnecting scan tool (M.U.T.-IIISE).
Connect scan tool (M.U.T.-IIISE). Refer to "How to connect Scan Tool (M.U.T.-IIISE) ."
(2) Erase the DTC.
(3) Turn on the corresponding light.
(4) Check if DTC No.B1E1D is set.
Is the DTC set?
Go to Step 5.
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to use Troubleshooting/inspection Service Points - How to Cope with Intermittent Malfunction ).
 
STEP 5. Using scan tool (M.U.T.-IIISE), Check whether the DTC is set again.
Check again if DTC No.B1E1D is set in the ETACS-ECU.
(1) Erase the DTC.
(2) Disconnect connector (a).
  1. Front dome light body
  2. Rear dome light body
  3. Luggage compartment light body
  4. Sun visor
(3) Turn on the corresponding light.
(4) Check if DTC No.B1E1D is set.
(5) Repeat steps (1) to (4) for parts (b) to (d) to determine a fault cause.
Is the DTC set?
Replace the ETACS-ECU.
Replace a defective bulb (the front dome light body, the rear dome light body, the luggage compartment light body or the sun visor).