[Previous][Next]
DTC B16A8: Taillight(LH) circuit short <Short circuit in the position light (LH) circuit, taillight (LH) circuit or the license plate light circuit>
 
 
cautionBefore replacing the ECU, ensure that the power supply circuit, the ground circuit and the communication circuit are normal.
 
 
DIAGNOSTIC FUNCTION
When a short circuit is detected in the position light circuit, the taillight circuit or the license plate light circuit, the ETACS-ECU sets DTC No. B16A8.
 
 
DTC SET CONDITION
The problem detection of taillight is made based on the digital feedback signal (input signal to ETACS-ECU) which operates the taillight. When the electric motor switch is ON, the ETACS-ECU determines the taillight circuit state from the load placed on the line. After 100 ms has elapsed since the start of the check, the ETACS-ECU performs a sampling with each 10 ms. If an abnormality is detected, it increases the counter by 2, and when no abnormality is detected, it decreases the counter by 1. Once the counter reaches "10," the ETACS-ECU sets DTC No. B16A8 if no load is detected.
 
 
TROUBLESHOOTING HINTS
  • The headlight assembly (LH) may be defective
  • The rear combination light assembly (LH) may be defective
  • The taillight assembly (LH) may be defective
  • The license plate light may be defective
  • The ETACS-ECU may be defective
  • The wiring harness or connectors may have loose, corroded, or damaged terminals, or terminals pushed back in the connector
 
 
DIAGNOSIS
Required Special Tools:
  • MB992006: Extra fine probe
  • MB991223: Harness set
STEP 1. Determine a trouble spot.
Which of light does not work?
: Go to Step 2.
: Go to Step 7.
: Go to Step 13.
: Go to Step 18.
 
STEP 2. Resistance measurement at the headlight assembly (position light/side marker light: LH) connector (ground terminal).
(1) Disconnect the connector, and measure at the wiring harness side.
(2) Measure the resistance between the headlight assembly (position light/side marker light: LH) connector (ground terminal) and ground.
OK: The resistance should be 2 ohms or less
Is the check result normal?
Go to Step 4.
Go to Step 3.
 
STEP 3. Check of open circuit in ground line between the headlight assembly (position light/side marker light: LH) connector and ground.
Is the check result normal?
Go to Step 5.
Repair the connector(s) or wiring harness.
 
STEP 4. Check of short to power supply, short to ground, and open circuit in TAL1 line between the headlight assembly (position light/side marker light: LH) connector and ETACS-ECU connector.
Is the check result normal?
Go to Step 5.
Repair the connector(s) or wiring harness.
 
STEP 5. Check whether the DTC is set again.
(1)
cautionTo prevent damage to scan tool (M.U.T.-IIISE), always turn off the power supply mode of the electric motor switch before connecting or disconnecting scan tool (M.U.T.-IIISE).
Connect scan tool (M.U.T.-IIISE). Refer to "How to connect Scan Tool (M.U.T.-IIISE) ."
(2) Erase the DTC.
(3) Press the electric motor switch to turn the power supply mode from "OFF" to "ON."
(4) Check if DTC is set.
Is the DTC set?
Go to Step 6.
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to use Troubleshooting/inspection Service Points - How to Cope with Intermittent Malfunction ).
 
STEP 6. Substitute a known good headlight assembly (LH), and check the DTC.
(1) Erase the DTC.
(2) Press the electric motor switch to turn the power supply mode from "OFF" to "ON."
(3) Check if DTC is set.
Is the DTC set?
Replace the ETACS-ECU.
Replace the headlight assembly (LH).
 
STEP 7. Check the rear combination light socket.
Check the continuity at the rear combination light socket to confirm whether it is normal.
Is the check result normal?
Go to Step 8.
Replace the rear combination light socket (LH).
 
STEP 8. Resistance measurement at the rear combination light (taillight/side marker light: LH) connector (ground terminal).
(1) Disconnect the connector, and measure at the wiring harness side.
(2) Measure the resistance between the rear combination light (taillight/side marker light: LH) connector (ground terminal) and ground.
OK: The resistance should be 2 ohms or less
Is the check result normal?
Go to Step 10.
Go to Step 9.
 
STEP 9. Check of open circuit in ground line between the rear combination light (taillight/side marker light: LH) connector and ground
Is the check result normal?
Go to Step 11.
Repair the connector(s) or wiring harness.
 
STEP 10. Check of short to power supply, short to ground, and open circuit in TAL2 line between the rear combination light (taillight/side marker light: LH) connector and ETACS-ECU connector.
Is the check result normal?
Go to Step 11.
Repair the connector(s) or wiring harness.
 
STEP 11. Check whether the DTC is set again.
(1)
cautionTo prevent damage to scan tool (M.U.T.-IIISE), always turn off the power supply mode of the electric motor switch before connecting or disconnecting scan tool (M.U.T.-IIISE).
Connect scan tool (M.U.T.-IIISE). Refer to "How to connect Scan Tool (M.U.T.-IIISE) ."
(2) Erase the DTC.
(3) Press the electric motor switch to turn the power supply mode from "OFF" to "ON."
(4) Check if DTC is set.
Is the DTC set?
Go to Step 12.
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to use Troubleshooting/inspection Service Points - How to Cope with Intermittent Malfunction ).
 
STEP 12. Substitute a known good rear combination light assembly (LH), and check the DTC.
(1) Erase the DTC.
(2) Press the electric motor switch to turn the power supply mode from "OFF" to "ON."
(3) Check if DTC is set.
Is the DTC set?
Replace the ETACS-ECU.
Replace the rear combination light assembly (LH).
 
STEP 13. Resistance measurement at the taillight (LH) connector (ground terminal).
(1) Disconnect the connector, and measure at the wiring harness side.
(2) Measure the resistance between the taillight (LH) connector (ground terminal) and the ground.
OK: The resistance should be 2 ohms or less
Is the check result normal?
Go to Step 15.
Go to Step 14.
 
STEP 14. Check of open circuit in ground lines between the taillight (LH) connector and ground.
Is the check result normal?
Go to Step 16.
Repair the connector(s) or wiring harness.
 
STEP 15. Check of short to power supply, short to ground, and open circuit in TAL2 line between the taillight (LH) connector and ETACS-ECU connector.
Is the check result normal?
Go to Step 16.
Repair the connector(s) or wiring harness.
 
STEP 16. Check whether the DTC is set again.
(1)
cautionTo prevent damage to scan tool (M.U.T.-IIISE), always turn off the power supply mode of the electric motor switch before connecting or disconnecting scan tool (M.U.T.-IIISE).
Connect scan tool (M.U.T.-IIISE). Refer to "How to connect Scan Tool (M.U.T.-IIISE) ."
(2) Erase the DTC.
(3) Press the electric motor switch to turn the power supply mode from "OFF" to "ON."
(4) Check if DTC is set.
Is the DTC set?
Go to Step 17.
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to use Troubleshooting/inspection Service Points - How to Cope with Intermittent Malfunction ).
 
STEP 17. Substitute a known good taillight assembly (LH), and check the DTC.
(1) Erase the DTC.
(2) Press the electric motor switch to turn the power supply mode from "OFF" to "ON."
(3) Check if DTC is set.
Is the DTC set?
Replace the ETACS-ECU.
Replace the taillight assembly (LH).
 
STEP 18. Bulb check.
Check the bulb(s) of the light that does not illuminate.
Is the check result normal?
Go to Step 19.
Replace the bulb(s) of the light that does not illuminate.
 
STEP 19. Resistance measurement at the license plate light (LH) or (RH) connector (ground terminal).
(1) Disconnect the connector, and measure at the wiring harness side.
(2) Measure the resistance between the license plate light (LH) or (RH) connector (ground terminal) and ground.
OK: The resistance should be 2 ohms or less
Is the check result normal?
Go to Step 21.
Go to Step 20.
 
STEP 20. Check of open circuit in ground line between the license plate light (LH) or (RH) connector and ground
Is the check result normal?
Go to Step 22.
Repair the connector(s) or wiring harness.
 
STEP 21. Check of short to power supply, short to ground, and open circuit in TAL2 line between the license plate light (LH) or (RH) connector and ETACS-ECU connector.
Is the check result normal?
Go to Step 22.
Repair the connector(s) or wiring harness.
 
STEP 22. Check whether the DTC is set again.
(1)
cautionTo prevent damage to scan tool (M.U.T.-IIISE), always turn off the power supply mode of the electric motor switch before connecting or disconnecting scan tool (M.U.T.-IIISE).
Connect scan tool (M.U.T.-IIISE). Refer to "How to connect Scan Tool (M.U.T.-IIISE) ."
(2) Erase the DTC.
(3) Press the electric motor switch to turn the power supply mode from "OFF" to "ON."
(4) Check if DTC is set.
Is the DTC set?
Go to Step 23.
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to use Troubleshooting/inspection Service Points - How to Cope with Intermittent Malfunction ).
 
STEP 23. Substitute a known good license plate light (LH) or (RH), and check the DTC.
(1) Erase the DTC.
(2) Press the electric motor switch to turn the power supply mode from "OFF" to "ON."
(3) Check if DTC is set.
Is the DTC set?
Replace the ETACS-ECU.
Replace the license plate light (LH) or (RH).