[Previous][Next]
DTC U1190: No receive fault detect signal
 
 
caution
  • If DTC U1190 is set, be sure to diagnose the CAN bus line.
  • When replacing the ECU, always check that the communication circuit is normal.
 
 
DIAGNOSTIC FUNCTION
When the signal from the ETACS-ECU cannot be received, OSS-ECU stores DTC U1190.
 
 
DTC SET CONDITION
Check Conditions
  • When all the following conditions are met.
    1. Power supply mode: ON
    2. ETACS-ECU system voltage is at 10 to 16 V.
Judgment Criterion
  • After the following condition is met, 5,000 ms or more have elapsed.
    1. CAN signal from the ETACS-ECU cannot be received.
 
 
TROUBLESHOOTING HINTS
  • Malfunction of the CAN bus line
  • Malfunction of ETACS-ECU
  • Malfunction of OSS-ECU
 
 
DIAGNOSIS
STEP 1. Using scan tool (M.U.T.-IIISE), diagnose the CAN bus line.
(1)
cautionTo prevent damage to scan tool (M.U.T.-IIISE), always turn the power supply mode of the electric motor switch to the OFF before connecting or disconnecting scan tool (M.U.T.-IIISE).
Connect scan tool (M.U.T.-IIISE). Refer to "How to connect scan tool (M.U.T.-IIISE) ."
(2) Turn the power supply mode of the electric motor switch to ON.
(3) Diagnose the CAN bus line.
(4) Turn the power supply mode of the electric motor switch to OFF.
Is the CAN bus line found to be normal?
Go to Step 2.
Repair the CAN bus line. (Refer to GROUP 54C, Diagnosis ).
 
STEP 2. Using scan tool (M.U.T.-IIISE), read the other system diagnostic trouble code.
Check if DTC is set in the ETACS-ECU.
(1)
cautionTo prevent damage to scan tool (M.U.T.-IIISE), always turn the power supply mode of the electric motor switch to the OFF before connecting or disconnecting scan tool (M.U.T.-IIISE).
Connect scan tool (M.U.T.-IIISE). Refer to "How to connect scan tool (M.U.T.-IIISE) ."
(2) Erase the DTC.
(3) Turn the power supply mode of the electric motor switch to ON.
(4) Check if DTC is set.
(5) Turn the power supply mode of the electric motor switch to OFF.
Is the DTC set?
Perform troubleshooting for ETACS (Refer to GROUP 54A, ETACS - Diagnosis ). Then go to Step 3.
Go to Step 3.
 
STEP 3. Using scan tool (M.U.T.-IIISE), read the other system diagnostic trouble code.
Check if DTC is set in the ETACS-ECU.
(1)
cautionTo prevent damage to scan tool (M.U.T.-IIISE), always turn the power supply mode of the electric motor switch to the OFF before connecting or disconnecting scan tool (M.U.T.-IIISE).
Connect scan tool (M.U.T.-IIISE). Refer to "How to connect scan tool (M.U.T.-IIISE) ."
(2) Erase the DTC.
(3) Turn the power supply mode of the electric motor switch to ON.
(4) Check if DTC is set.
(5) Turn the power supply mode of the electric motor switch to OFF.
Is the DTC set?
Replace the ETACS-ECU (Refer to GROUP 54A, ETACS - ETACS-ECU ).
Go to Step 4.
 
STEP 4. Recheck for diagnostic trouble code.
Check again if the DTC is set in the OSS-ECU.
(1) Erase the DTC.
(2) Turn the power supply mode of the electric motor switch from OFF to ON.
(3) Check if DTC is set.
(4) Turn the power supply mode of the electric motor switch from ON to OFF.
Is the DTC set?
Replace the OSS-ECU and register the VIN (Refer to ).
Intermittent malfunction is suspected (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to cope with Intermittent Malfunction ).