[Previous][Next]
DTC B2400: F.A.S.T. key registration fail
 
 
caution
  • If the DTC B2400 is set, diagnose the CAN bus lines.
  • When replacing the ECU, always check that the communication circuit is normal.
 
 
DIAGNOSTIC FUNCTION
If the registration of the keyless operation key ID to KOS-ECU fails, KOS-ECU sets diagnostic trouble code No. B2400.
 
 
TECHNICAL DESCRIPTION (COMMENT)
Assuming that another keyless operation key has already been registered with KOS-ECU, if the registration of the keyless operation key ID fails when a new keyless operation key is added or the existing key is replaced, KOS-ECU determines that there is a problem.
 
 
TROUBLESHOOTING HINTS
  • At the registration, there is an object near the keyless operation key which interferes with the communication.
  • Wrong keyless operation key registration method
  • Failure of keyless operation key code registration
  • Battery drain of keyless operation key
  • Malfunction of the keyless operation key
  • Malfunction of CAN bus line
  • Malfunction of OSS-ECU
  • Malfunction of KOS-ECU
 
 
DIAGNOSIS
STEP 1. Interference check at keyless operation key registration
At the keyless operation key registration, check if there is another key nearby or anything that interferes with the communication (magnets or objects that generate radio waves such as air-cleaning devices with a power plug).
Are there other keys or anything that interferes with the communication?
Move away or remove other keys or anything that interferes with the communication.
Go to Step 2.
 
STEP 2. Check of keyless operation key registration method
Check that the correct method was used at the registration of keyless operation key.
Is the check result normal?
Go to Step 3.
Register the keyless operation key.(Refer to .)
 
STEP 3. Using scan tool (M.U.T.-IIISE), diagnose the CAN bus line.
(1)
cautionTo prevent damage to scan tool (M.U.T.-IIISE), always turn the power supply mode of the electric motor switch to the OFF before connecting or disconnecting scan tool (M.U.T.-IIISE).
Connect scan tool (M.U.T.-IIISE). Refer to "How to connect scan tool (M.U.T.-IIISE) ."
(2) Turn the power supply mode of the electric motor switch to ON.
(3) Diagnose the CAN bus line.
(4) Turn the power supply mode of the electric motor switch to OFF.
Is the CAN bus line found to be normal?
Go to Step 4.
Repair the CAN bus line. (Refer to GROUP 54C, Diagnosis ).
 
STEP 4. Using scan tool (M.U.T.-IIISE), read the diagnostic trouble code.
(1)
cautionTo prevent damage to scan tool (M.U.T.-IIISE), always turn the power supply mode of the electric motor switch to the OFF before connecting or disconnecting scan tool (M.U.T.-IIISE).
Connect scan tool (M.U.T.-IIISE). Refer to "How to connect scan tool (M.U.T.-IIISE) ."
(2) Turn the power supply mode of the electric motor switch to ON.
(3) Check if any DTC is set in the KOS-ECU.
(4) Turn the power supply mode of the electric motor switch to OFF.
Is the DTC set?
Refer to diagnostic trouble code chart .
Go to Step 5.
 
STEP 5. Using scan tool (M.U.T.-IIISE), read the other system diagnostic trouble code.
(1)
cautionTo prevent damage to scan tool (M.U.T.-IIISE), always turn the power supply mode of the electric motor switch to the OFF before connecting or disconnecting scan tool (M.U.T.-IIISE).
Connect scan tool (M.U.T.-IIISE). Refer to "How to connect scan tool (M.U.T.-IIISE) ."
(2) Turn the power supply mode of the electric motor switch to ON.
(3) Check if any DTC is set in the OSS-ECU.
(4) Turn the power supply mode of the electric motor switch to OFF.
Is the DTC set?
Perform troubleshooting for the OSS-ECU (Refer to diagnostic trouble code chart ). On completion, go to Step 6.
Go to Step 6.
 
STEP 6. Replace the battery in the keyless operation key and recheck the diagnostic trouble code.
Replace the battery of the keyless operation key for which the DTC is set, and check whether the DTC is set again.
(1) Turn the power supply mode of the electric motor switch from OFF to ON.
(2) Check if the DTC is set.
Is the DTC set?
Go to Step 7.
The procedure is complete (Discharged battery).
 
STEP 7. Replace the keyless operation key and recheck the diagnostic trouble code.
Replace the keyless operation key for which the DTC is set with a new one, register the encrypted code and keyless operation key ID (refer to ), and check whether the DTC is set again.
(1) Turn the power supply mode of the electric motor switch from OFF to ON.
(2) Check if the DTC is set.
Is the DTC set?
Go to Step 8.
The procedure is complete.
 
STEP 8. Check whether the diagnostic trouble code is set again.
(1) Turn the power supply mode of the electric motor switch from OFF to ON.
(2) Check if the DTC is set.
Is the DTC set?
Replace KOS-ECU and register the ID codes (Refer to ).
The procedure is complete.