35A-MAINTENANCE MODE

MAINTENANCE MODE

When the system enters the maintenance mode, the electric parking brake will be released completely. Then you can push back the brake piston to replace the rear brake pad or the rear disc brake rotor. Use the scan tool (M.U.T.-IIISE) or the switch to make the system enter the maintenance mode.

Use the scan tool (M.U.T.-IIISE) to make the system enter the maintenance mode.

Required Special Tools:

MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
MB992745: V.C.I.-Lite main harness A
MB992747: V.C.I.-Lite USB cable short
MB992748: V.C.I.-Lite USB cable long
MB991958: Scan Tool (M.U.T.-III Sub Assembly)

MB991824: Vehicles Communication Interface (V.C.I.)
MB991827: M.U.T.-III USB Cable
MB991910: M.U.T.-III Main Harness A (Vehicles with CAN communication system)

1. Raise the vehicle using a jack and support the specified points with a rigid rack.

2. Turn off the power supply mode of the electric motor switch.

caution

To prevent damage to scan tool (M.U.T.-IIISE), always turn off the power supply mode of the electric motor switch before connecting or disconnecting scan tool (M.U.T.-IIISE).

Connect scan tool (M.U.T.-IIISE). Refer to "How to connect the Scan Tool (M.U.T.-IIISE)

4. Move the selector lever to "P" position, and turn on the power supply mode of the electric motor switch (but do not start the motor (Electric motor unit)).

5. Depress the brake pedal.

note	Keep the brake pedal depressed until the power supply mode of the electric motor switch is turned off.

6. Operate the scan tool (M.U.T.-IIISE) as below:

(1) Select "EPB" on the system selection screen.

(2) Select "Actuator Test".

(3) Select "Full release control".

7. The brake warning light (red) and electric parking brake switch indicator light should blink, and the system should enter the maintenance mode.

note	Once the system has entered the maintenance mode, the electric parking brake is released completely.

caution

Do not operate the electric parking brake switch to apply the parking brake. If yes, the maintenance mode will be cancelled.
When the electric parking brake switch is pulled up even with the power supply mode of the electric motor switch OFF, the maintenance mode will be cancelled.

Release the brake pedal.

9. Turn off the power supply mode of the electric motor switch.

10. Disconnect the negative battery terminal of the 12V Starter Battery.

Use the switch to make the system enter the maintenance mode.

note	Use the switch only if the scan tool (M.U.T.-IIISE) is not available.

1. Raise the vehicle using a jack and support the specified points with a rigid rack.

2. Move the selector lever to "P" position, and turn on the power supply mode of the electric motor switch (but do not start the motor (Electric motor unit)).

3. Depress the brake pedal.

note	Keep the brake pedal depressed until the power supply mode of the electric motor switch is turned off.

caution

Do not operate the electric parking brake switch too quickly (wait for at least two seconds by the next switch operation). If yes, the ECU can not recognize the switch operation. This may cause the indicator light or the warning light not to flash.
It is necessary to execute Step 5 and Step 6 within 7 seconds after executing Step 4 (brake warning light (red) and electric parking brake switch indicator light flashing).

Operate the electric parking brake switch and alternately apply and release the parking brake 10 times, and the brake warning light (red) and the electric parking brake switch indicator light will flash.

note	The multi-information display should show "PARKING BRAKE TEMPORARILY NOT AVAILABLE".

5. Operate the electric parking brake switch once to release the parking brake.

6. Press the brake auto hold switch 10 time or more as soon as possible, then perform the release operation of the electric parking brake switch once.

7. After the system enters the maintenance mode, the electric parking brake warning light (yellow) will stay on (do not flash anymore).

note

The multi-information display should show "PARKING BRAKE SERVICE REQUIRED".
Once the system has entered the maintenance mode, the electric parking brake is released completely.
If you failed the operation of the switch and did not enter maintenance mode, repeat the procedure after 60 seconds have elapsed.

caution

Do not operate the electric parking brake switch to apply the parking brake. If yes, the maintenance mode will be cancelled.
When the electric parking brake switch is pulled up even with the power supply mode of the electric motor switch OFF, the maintenance mode will be cancelled.

Release the brake pedal.

9. Turn off the power supply mode of the electric motor switch.

10. Disconnect the negative battery terminal of the 12V Starter Battery.

How to resume normal operation mode

1. Reconnect the negative battery terminal of the 12V Starter Battery.

2. Turn on the power supply mode of the electric motor switch.

3. The warning light, the indicator light and the multi-information display should be activated as follows:

When you made the system enter the maintenance mode by using the scan tool (M.U.T.-IIISE)

Brake warning light (red): blinks
Electric parking brake switch indicator light: blinks

When you made the system enter the maintenance mode by using the switch

Electric parking brake warning light (yellow): illuminates
Brake warning light (red): blinks
Electric parking brake switch indicator light: blinks
Multi-information display: PARKING BRAKE SERVICE REQUIRED

note	If the system enters the maintenance mode unintentionally, turn off the power supply mode of the electric motor switch and wait for at least 60 seconds. Then turn on the power supply mode of the electric motor switch.

4. Operate the electric parking brake switch to apply the parking brake.

5. When the normal operation mode has been resumed, the brake warning light (red) and the electric parking brake switch indicator light should stay on (do not flash anymore).