[Previous][Next]
INSPECTION
 
 
SELECTOR LEVER ASSEMBLY CHECK
Observe the following chart to check the selector lever assembly. If defective, replace the selector lever assembly.
  • To measure the voltage, connect the connector to the selector lever assembly. Then turn on the power supply mode of the electric motor switch to measure the voltage at the wiring harness side.

Terminal numberItemSelector lever positionStandard value
7 - 8Shift sensor (main)Is not operated2.3 - 2.7 V
Is held at N position
Is held at R position0.59 - 1.49 V
Is held at D position3.5 - 4.4 V
Is held at B position
3 - 4Shift sensor (sub)Is not operated2.3 - 2.7 V
Is held at N position
Is held at R position3.5 - 4.4 V
Is held at D position0.59 - 1.49 V
Is held at B position
5 - 8Select sensor (main)Is not operated2.32 - 2.57 V
Is held at N position4.27 - 4.39 V
Is held at R position
Is held at D position
Is held at B position2.32 - 2.57 V
1 - 4Select sensor (sub)Is not operated2.32 - 2.57 V
Is held at N position4.27 - 4.39 V
Is held at R position
Is held at D position
Is held at B position2.32 - 2.57 V
 
 
 
EV PRIORITY MODE SWITCH, SAVE/CHARGE MODE SWITCH AND POSITION INDICATOR CHECK
Observe the following chart to check the EV priority mode switch, SAVE/CHARGE mode switch and position indicator. If defective, replace the sift indicator panel.

EV PRIORITY MODE SWITCH, SAVE/CHARGE MODE SWITCH CHECK
Terminal numberItemEV priority mode switch and SAVE/CHARGE mode switch operationNormal conditions
Continuity (Resistance)Illumination/extinction
1 - 8SAVE/CHARGE mode switchDon not press the switchNo continuity-
Press and hold the switchContinuity exists (2Ω or less)-
2 - 9EV priority mode switchDon not press the switchNo continuity-
Press and hold the switchContinuity exists (2Ω or less)-
7 - 14EV priority mode and SAVE/CHARGE mode indicatorDon not illuminate the position lampNo continuity-
Illuminate the position lampNo continuityIllumination
POSITION INDICATOR CHECK
Terminal numberItemSelector lever operationNormal conditions
Continuity (Resistance)Illumination/extinction
4 - 5Position indicator (R)RNo continuityIllumination
4 - 6Position indicator (N)NNo continuityIllumination
4 - 12Position indicator (D)DNo continuityIllumination
4 - 13Position indicator (B)BNo continuityIllumination
2 - 9EV priority mode switchDon not press the switchNo continuity-
Press and hold the switchContinuity exists (2Ω or less)-
1 - 8SAVE/CHARGE mode switchDon not press the switchNo continuity-
Press and hold the switchContinuity exists (2Ω or less)-
 
 
 
ELECTRICAL PARKING SWITCH CHECK
Observe the following chart to check the electric parking switch. If defective, replace the sift indicator panel.

Terminal numberItemElectrical parking switch operation*Normal conditions
Continuity (Resistance)Illumination/extinction
4 - 5Electrical parking switch (main)Don not press the switchContinuity exists (150 - 170 Ω)-
Press and hold the switchContinuity exists (5.9 - 6.6 kΩ)-
6 - 7Electrical parking switch (sub)Don not press the switchContinuity exists (5.9 - 6.6 kΩ)-
Press and hold the switchContinuity exists (150 - 170 Ω)-
1 - 4Indicator-No continuityConnect the connector to the electric parking switch. When the power supply mode of the electric motor switch is on or the ready indicator illuminates, the indicator must illuminate.
Connect the connectors to the electric parking switch and the selector lever assembly. When the power supply mode of the electric motor switch is turned on with the brake pedal depressed and the selector lever is tilted towards N position, the indicator must go out.
3 - 8Illumination-No continuityConnect the connector to the electric parking switch. When the taillight illuminate, "P" must illuminate.