STEP 1. Checking with audio speaker test.
STEP 2. Check the speaker, tweeter or subwoofer.
(1) Remove the speaker, tweeter or subwoofer.
(2) Check that the speaker, tweeter or subwoofer outputs the noise when the voltage of 5 volts is applied to the speaker, tweeter or subwoofer connector terminal.
Is the check result normal?
: Go to Step 5. : Go to Step 3. Replace the speaker, tweeter or subwoofer.
STEP 3. Check the wiring harness between the emergency call relay box connector terminal and the audio amplifier connector terminal.
STEP 4. Check the wiring harness between the front door speaker (RH) connector terminal and the emergency call relay box connector terminal.
STEP 5. Check the wire harness between the speaker, tweeter or subwoofer connector terminal and the audio amplifier connector terminal.
Front door speaker (LH)
- Check of short circuit in DFL+, DFL- line between front door speaker (LH) connector and audio amplifier connector.
Front door speaker (RH) <Vehicles without MITSUBISHI CONNECT Safeguard Services and Remote Services>
- Check of short circuit in DFR+, DFR- line between front door speaker (RH) connector and audio amplifier connector.
Front tweeter (LH)
- Check of short circuit in TFL+, TFL- line between front door speaker (LH) connector and audio amplifier connector.
Front tweeter (RH)
- Check of short circuit in TFR+, TFR- line between front door speaker (RH) connector and audio amplifier connector.
Rear door speaker (LH)
- Check of short circuit in RL+, RL- line between front door speaker (LH) connector and audio amplifier connector.
Rear door speaker (RH)
- Check of short circuit in RR+, RR- line between front door speaker (RH) connector and audio amplifier connector.
Subwoofer
- Check of short circuit in RW+, RW1+, RW-, RW1- line between subwoofer connector and audio amplifier connector.
Is the check result normal?
Go to Step 6. Repair the connector(s) or wiring harness. (Replace the harness assembly because the aluminum harness cannot be repaired.)
STEP 6. Check of short to power supply, short to ground, and open circuit in FL+, FL-, FR+, FR-, RR+ and RR- lines between audio amplifier connector and multivision display connector.
STEP 7. Check the speaker, tweeter or subwoofer.
Follow the speaker test to check which speaker, tweeter or subwoofer does not sound.(1) Remove the speaker, tweeter or subwoofer.
(2) Check that the speaker, tweeter or subwoofer outputs the noise when the voltage of 5 volts is applied to the speaker, tweeter or subwoofer connector terminal.
Do the speaker output the noise?
: Go to Step 10. : Go to Step 8. Replace the speaker, tweeter or subwoofer.
STEP 8. Check the wiring harness between the emergency call relay box connector terminal and the audio amplifier connector terminal.
STEP 9. Check the wiring harness between the front door speaker (RH) connector terminal and the emergency call relay box connector terminal.
STEP 10. Check the wire harness between the speaker, tweeter or subwoofer connector terminal and audio amplifier connector terminal.
Follow the speaker test to check which speaker, tweeter or subwoofer circuit is defective.Front door speaker (LH)
- Check of short circuit in DFL+, DFL- line between front door speaker (LH) connector and audio amplifier connector.
Front door speaker (RH) <Vehicles without MITSUBISHI CONNECT Safeguard Services and Remote Services>
- Check of short circuit in DFR+, DFR- line between front door speaker (RH) connector and audio amplifier connector.
Front tweeter (LH)
- Check of short circuit in TFL+, TFL- line between front door speaker (LH) connector and audio amplifier connector.
Front tweeter (RH)
- Check of short circuit in TFR+, TFR- line between front door speaker (RH) connector and audio amplifier connector.
Rear door speaker (LH)
- Check of short circuit in RL+, RL- line between front door speaker (LH) connector and audio amplifier connector.
Rear door speaker (RH)
- Check of short circuit in RR+, RR- line between front door speaker (RH) connector and audio amplifier connector.
Subwoofer
- Check of short circuit in RW+, RW1+, RW-, RW1- line between subwoofer connector and audio amplifier connector.
Is the check result normal?
Go to Step 11. Repair the connector(s) or wiring harness. (Replace the harness assembly because the aluminum harness cannot be repaired.)
STEP 11. Check of short to power supply, short to ground, and open circuit in FL+, FL-, FR+, FR-, RR+ and RR- lines between audio amplifier connector and multivision display connector.
STEP 12. Retest the system.