[Previous][Next]
DTC P0137: Heated Oxygen Sensor (rear) Circuit Low Voltage
 
 
 
 
CIRCUIT OPERATION
  • A voltage corresponding to the oxygen concentration in the exhaust gas is sent to the ECM terminal O2RL from the output terminal of the heated oxygen sensor (rear).
  • Terminal ORLE line of the heated oxygen sensor (rear) is grounded with ECM terminal ORLE.
  • The ECM applies an offset voltage of 0.5 volt to ground terminal of the heated oxygen sensor (rear).
 
 
TECHNICAL DESCRIPTION
  • The output signal of the linear air-fuel ratio sensor is compensated by the output signal of the heated oxygen sensor (rear).
  • The ECM checks for the heated oxygen sensor (rear) output voltage.
 
 
DESCRIPTIONS OF MONITOR METHODS
  • Heated oxygen sensor (rear) output voltage is under the specified range.
 
 
MONITOR EXECUTION
  • Continuous
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC set in memory for the item monitored below)
  • Linear air-fuel ratio sensor heater monitor
  • Heated oxygen sensor (rear) heater monitor
  • Heated oxygen sensor offset voltage monitor
Sensor (The sensor below is determined to be normal)
  • Linear air-fuel ratio sensor
  • Mass airflow sensor
  • Engine coolant temperature sensor
  • Intake air temperature sensor 1
  • Barometric pressure sensor
 
 
DTC SET CONDITIONS
Logic Flow Chart
 
 
Check Conditions
  • Heated oxygen sensor offset voltage is between 0.4 and 0.6 volt.
  • Battery positive voltage is between 11 and 16.5 volts.
  • More than 3 minutes have passed since the engine starting sequence was completed.
Judgment Criterion
  • Heated oxygen sensor (rear) output voltage is lower than 0.2 volt for 2 seconds.
 
 
FAIL-SAFE AND BACKUP FUNCTION
None.
 
 
OBD-II DRIVE CYCLE PATTERN
  • Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 2 .
 
 
TROUBLESHOOTING HINTS (The most likely causes for this code to be set are: )
  • Heated oxygen sensor (rear) failed.
  • Open or shorted heated oxygen sensor (rear) circuit, harness damage or connector damage.
  • ECM failed.

 
 
DIAGNOSIS
Required Special Tool:
  • MB991658: Test Harness
STEP 1. Using scan tool (M.U.T.-IIISE), check data list item AD: Heated Oxygen Sensor (rear).
cautionTo prevent damage to scan tool (M.U.T.-IIISE), always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool (M.U.T.-IIISE).
(1) Connect scan tool (M.U.T.-IIISE). Refer to HOW TO CONNECT THE SCAN TOOL (M.U.T.-IIISE) .
(2) Start the engine and run at idle.
(3) Set scan tool (M.U.T.-IIISE) to the data reading mode for item AD, Heated Oxygen Sensor (rear).
  1. Transaxle: 2nd
  2. Drive with wide open throttle
  3. Engine: 3,500 r/min or more
    • The output voltages should be between 0.6 and 1.0 volt.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the sensor operating properly?
It can be assumed that this malfunction is intermittent. Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions .
Go to Step 2.
 
STEP 2. Measure the voltage at heated oxygen sensor (rear) connector.
(1) Disconnect the heated oxygen sensor (rear) connector and measure at the harness side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal ORLE line and ground.
  • Voltage should be between 0.4 and 0.6 volt.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the measured voltage between 0.4 and 0.6 volt?
Go to Step 4.
Go to Step 3.
 
STEP 3. Check of open circuit and short circuit in ORLE line between heated oxygen sensor (rear) connector and ECM connector.
Is the harness wire in good condition?
Go to Step 9.
Repair the connector(s) or wiring harness. Then go to Step 10.
 
STEP 4. Check of harness damage in ORLE line between heated oxygen sensor (rear) connector and ECM connector.
Is the harness wire in good condition?
Go to Step 5.
Repair the connector(s) or wiring harness. Then go to Step 10.
 
STEP 5. Measure the sensor output voltage at heated oxygen sensor (rear) connector.
(1) Disconnect the heated oxygen sensor (rear) connector and connect test harness special tool MB991658 to the connector on the heated oxygen sensor (rear) side.
(2) Start the engine and run at idle.
(3) Measure the voltage between terminal O2RL line and ground.
  1. Transaxle: 2nd
  2. Drive with wide open throttle
  3. Engine: 3,500 r/min or more
    • The output voltage should be between 1.0 and 1.5 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Is the measured voltage within the specified range?
Go to Step 8.
Go to Step 6.
 
STEP 6. Check the heated oxygen sensor (rear).
Refer to Heated Oxygen Sensor (Rear) .
Is the heated oxygen sensor (rear) normal?
Go to Step 7.
Replace the heated oxygen sensor (rear). Then go to Step 10.
 
STEP 7. Check of short circuit to ground in O2RL line between heated oxygen sensor (rear) connector and ECM connector.
Is the harness wire in good condition?
Go to Step 9.
Repair the connector(s) or wiring harness. Then go to Step 10.
 
STEP 8. Check of open circuit and harness damage to ground in O2RL line between heated oxygen sensor (rear) connector and ECM connector.
Is the harness wire in good condition?
Go to Step 9.
Repair the connector(s) or wiring harness. Then go to Step 10.
 
STEP 9. Using scan tool (M.U.T.-IIISE), check data list item AD: Heated Oxygen Sensor (rear).
(1) Start the engine and run at idle.
(2) Set scan tool (M.U.T.-IIISE) to the data reading mode for item AD, Heated Oxygen Sensor (rear).
  1. Transaxle: 2nd
  2. Drive with wide open throttle
  3. Engine: 3,500 r/min or more
    • The output voltage should be between 0.6 and 1.0 volt.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Is the sensor operating properly?
It can be assumed that this malfunction is intermittent. Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions .
Replace the ECM (Refer to Removal and Installation ). Then go to Step 10.
 
STEP 10. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 2 .
(2) Check the diagnostic trouble code (DTC).
Is DTC P0137 set?
Retry the troubleshooting.
The inspection is complete.