00-CONFIGURATION FUNCTION

CUSTOMIZATION FUNCTION

ETACS CUSTOMIZATION

Using the ETACS system of scan tool (M.U.T.-IIISE), the following functions can be programmed. The programmed information is held even when the battery is disconnected.

Adjustment item (scan tool display)	Adjustment item	Adjusting content (scan tool display)	Adjusting content
Turn power source	Adjustment of turn-signal light operation condition	ACC or IG1	Operable with ACC or ON position
Turn power source	Adjustment of turn-signal light operation condition	IG1	Operable with ON position (initial condition)
Comfort flasher	With/without comfort flasher function	Disable	No function
Comfort flasher	With/without comfort flasher function	Enable	With function (initial condition)
Hazard answer back	Adjustment of the number of keyless hazard warning light answer back flashes	Lock: 1, Unlock: 2	LOCK: Flashes once, UNLOCK: Flashes twice (initial condition)
		Lock: 1, Unlock: 0	LOCK: Flashes once, UNLOCK: No flash
		Lock: 0, Unlock: 2	LOCK: No flash, UNLOCK: Flash twice
		Lock: 2, Unlock: 1	LOCK: Flash twice, UNLOCK: Flash once
		Lock: 2, Unlock: 0	LOCK: Flash twice, UNLOCK: No flash
		Lock: 0, Unlock: 1	LOCK: No flash, UNLOCK: Flash once
		Lock: 0, Unlock: 0	No function
Front wiper operation	Adjustment of the intermittent windshield wiper operation <Vehicles without lighting control sensor>	Normal INT	Intermittent wiper interval is fixed to 4 seconds.
		Variable INT	Intermittent wiper interval is calculated only by the wiper volume control.
		Speed Sensitive	Intermittent wiper interval is calculated according to the intermittent wiper volume control and vehicle speed (initial condition).
	Adjustment of the intermittent windshield wiper operation <Vehicles with lighting control sensor>	Normal INT	Intermittent wiper interval is fixed to 4 seconds.
		Variable INT	Intermittent wiper interval is calculated only by the wiper volume control.
		Speed Sensitive	Intermittent wiper interval is calculated according to the intermittent wiper volume control and vehicle speed.
		Rain Sensitive	Intermittent wiper interval is calculated according to the intermittent wiper volume control and lighting control sensor (initial condition).
Front/rear wiper washer	Disabling or enabling washer-linked wiper function	Only Washer	No function
		Washer & Wiper	With function: Without delayed finishing wipe function (initial condition)
		Washer & Wiper with after wiper	With function: With delayed finishing wipe function
Intermittent time of rear wiper	Adjustment of rear wiper interval	0 sec.	No wiper interval
		4 sec.	4 seconds
		8 sec.	8 seconds (initial condition)
		16 sec.	16 seconds
Rear wiper low speed mode	Disabling or enabling rear wiper continuous operation	Disable	No function
Rear wiper low speed mode	Disabling or enabling rear wiper continuous operation	Enable	With function (initial condition)
Auto fold mirror	Electric folding door mirror automatic unfolding function <Vehicles with electric retractable remote controlled door mirrors>	Not Auto	No synchronized operation
		Open by vehicle speed	Vehicle speed-dependent operation
		Open/Close by IG	Ignition switch linked operation
		Open/Close by Keyless	Keyless entry linked operation (initial condition)
Sensitivity for auto lamp	Lighting control sensor sensitivity (illumination intensity) <Except vehicles for CANADA>	Level 1 bright	High-high ambient brightness
		Level 2 bright	High ambient brightness
		Level 3	Standard ambient brightness (initial condition)
		Level 4 dark	Low ambient brightness
		Level 5 dark	Low-low ambient brightness
Room lamp delay timer with door	Adjustment of interior light delay shutdown time	0 sec.	0 second (no delay shutdown time)
		7.5 sec.	7.5 seconds
		15 sec.	15 seconds
		30 sec.	30 seconds (initial condition)
		60 sec.	60 seconds
		120 sec.	120 seconds
		180 sec.	180 seconds
Head lamp auto cut customize	Adjustment of headlight automatic shutdown function	Disable	No function
Head lamp auto cut customize	Adjustment of headlight automatic shutdown function	Enable (C-spec.)	With function (initial condition)
Interior lamp auto cut timer	Adjustment of interior light automatic shutdown function operation time	Disable	No function
		3 min	3 minutes
		30 min	30 minutes (initial condition)
		60 min	60 minutes
Auto door unlock	Adjustment of the auto door unlock function	Disable	Without function (initial condition)
		Always(Shift P position)	With function: Operates when the shift lever or the selector lever is moved to the P position.
		Always(IG lock position)	With function: Operates when the ignition switch is moved to the LOCK (OFF) position.
Door unlock mode	Adjustment of power door locks with selective unlocking	All Doors unlock	Without function: The first operation of keyless entry system or unlock operation by KOS unlocks all doors.
Door unlock mode	Adjustment of power door locks with selective unlocking	Driver's door unlock	With function: The first operation of keyless entry system or unlock operation by KOS unlocks the driver's door only, and the second unlock operation within 2 seconds after that unlocks all doors (initial condition).
Buzzer answer back	Adjusts the tone alarm answer back function. <Vehicles with KOS>	Not sound buzzer	Without function
		At keyless	Sounds when the keyless entry system is activated.
		At KOS	Sounds when KOS is activated (initial condition).
		At Both	Sounds when the keyless entry system or KOS is activated.
Horn chirp by keyless	Horn chirp by keyless entry system <Vehicles without lighting control sensor>	Not sound horn	No horn answerback function
		Every lock any time	The horn sounds when the lock button of keyless entry transmitter is pressed once.
		Double lock any time	The horn sounds when the lock button of keyless entry transmitter is pressed twice. (initial condition)
	Horn chirp by keyless entry system <Vehicles with lighting control sensor>	Not sound horn	No horn answerback function
		Every lock any time	The horn sounds when the lock button of keyless entry transmitter is pressed once.
		Lock daytime + Auto light ON	During daytime, while the lighting switch is in the AUTO position, the horn sounds once when the lock is pressed once.
		Double lock any time	The horn sounds when the lock button of keyless entry transmitter is pressed twice. (initial condition)
Timer lock timer	Timer lock period adjustment	30 sec.	30 seconds (initial condition)
		60 sec.	60 seconds
		120 sec.	120 seconds
		180 sec.	180 seconds
Multi mode	Multi-mode keyless entry function customization <Up to 18 Model year and vehicles with electric retractable remote controlled door mirrors>	Disable	No function
Multi mode		D/M: Open & Close	Door mirror fold/unfold operation only (initial condition)
Panic alarm switch	With/without panic alarm function	Disable	No function
Panic alarm switch	With/without panic alarm function	Enable	With function (initial condition)
Duration of horn chirp	Horn sounding time during horn answer back	Short	0.01 second (initial condition)
Duration of horn chirp	Horn sounding time during horn answer back	Long	0.02 second
F.A.S.T.^* key detect out from window	With/without KOS key exterior detection function <Vehicles with KOS>	Disable	No function (initial condition)
F.A.S.T.^* key detect out from window		Enable	With function
F.A.S.T.^* feature	KOS function adjustment <Vehicles with KOS>	Both enable	All KOS functions are enabled (initial condition).
		Door entry enable	Only door entry function is enabled.
		ENG start enable	Only engine starting function is enabled.
		Both disable	All KOS functions are disabled.
F.A.S.T.^* unlock disable time	Adjusts the door unlock inhibition period by the liftgate open switch after door lock is activated. <Vehicles with KOS>	0 sec.	0 second
		3 sec.	3 seconds (initial condition)
		5 sec.	5 seconds
Remote ENG starter answer back	Remote engine starter answer back function adjustment <Up to 20 Model year>	Disable	No function (initial condition)
Remote ENG starter answer back		Enable	With function
ACC power auto cut time	Time to ACC power cut-off when the ignition switch is in the ACC position	Disable	No function
		30 min	30 minutes (initial condition)
		60 min	60 minutes
Comfort flasher switch time	Switch operation time to activate the comfort flasher function	Normal	0.4 second (initial condition)
Comfort flasher switch time		Long	0.8 second
Intelligent washer	With/without Comfort washer function	Disable	No function
Intelligent washer	With/without Comfort washer function	Enable	With function (initial condition)
Coming home light	Disabling or enabling coming home light function	Disable	No function
		15 sec.	The headlights illuminate for 15 seconds.
		30 sec.	The headlights illuminate for 30 seconds. (initial condition)
		60 sec.	The headlights illuminate for 60 seconds.
		180 sec.	The headlights illuminate for 180 seconds.
Welcome light	Disabling or enabling welcome light function	Disable	No function
		Small light	The taillight illuminates. (initial condition)
		Headlight	The headlight illuminates.
Rear wiper (linked reverse gear)	Adjustment of automatic rear window wiper operation with reverse gear engaged	Enable(Rear wiper ON)	Operates only when the rear wiper switch is ON.
Rear wiper (linked reverse gear)		Enable(Rear/Front wiper ON)	Operates only when the front or rear wiper switch is ON (initial condition).
Outer buzzer volume	KOS outer buzzer volume adjustment <Vehicles with KOS>	Volume 1	Quieter than the standard
		Volume 2	Standard volume (initial condition)
		Volume 3	Louder than the standard
A/C recirculation control	With/without inside/outside air automatic control function	Disable	No function
A/C recirculation control	With/without inside/outside air automatic control function	Enable	With function (initial condition)
A/C switch control	With/without A/C automatic control function	Disable	No function
A/C switch control	With/without A/C automatic control function	Enable	With function (initial condition)
A/C sensible temperature customize	Adjusting mean value for temperature setting	-2	Decreases the control temperature two degrees than the temperature displayed on the LCD.
		-1	Decreases the control temperature one degree than the temperature displayed on the LCD.
		0	No change (initial condition)
		1	Increases the control temperature one degree than the temperature displayed on the LCD.
		2	Increases the control temperature two degrees than the temperature displayed on the LCD.
ECO mode	Function to activate ECO mode air-conditioner	ECO	Activates the ECO mode (initial condition).
ECO mode	Function to activate ECO mode air-conditioner	Comfort	Deactivates the ECO mode.
FOOT / DEF air outlet ratio	Changes air distribution rate for DEF/FOOT vents during manual operation.	Normal	D/F2 (initial condition)
		FOOT > DEF	D/F1(more to FOOT vent): More air flows through FOOT vents.
		FOOT < DEF	D/F3(more to DEF vent): More air flows through DEF vents.
FACE / FOOT air outlet ratio	Changes air distribution rate for FACE/FOOT vents during manual operation.	Normal	B/L2 (initial condition)
		FACE > FOOT	B/L1(more to FACE vent): More air flows through FACE vents.
		FACE < FOOT	B/L3(more to FOOT vent): More air flows through FOOT vents.
Auto rear defogger (Engine start)	Activates the rear window defogger when the ambient temperature is low. (The rear window defogger has never been activated since the ignition switch was turned on last time)	Disable	No function (initial condition)
Auto rear defogger (Engine start)		Enable	With function
Headlight control time (EV REMOTE car finder) <Vehicles with TCU>	Time adjustment of the headlight by using the MITSUBISHI CONNECT Remote services	Disable	Without function
		15 sec	15 sec.
		30 sec	30 sec (initial condition)
		45 sec	45 sec.
Position light control time (EV REMOTE car finder) <Vehicles with TCU>	Time adjustment of the position light by using the MITSUBISHI CONNECT Remote services	Disable	Without function
		15 sec	15 sec.
		30 sec	30 sec (initial condition)
		45 sec	45 sec.
Horn control times (EV REMOTE car finder) <Vehicles with TCU>	Time adjustment of the horn by using the MITSUBISHI CONNECT Remote services	Disable	Without function
		Once	Once.
		Twice	Twice. (initial condition)
		3 times	3 times.

note	*: F.A.S.T. (Free-hand Advanced Security Transmitter)

COMBINATION METER (CHANGE THE TURN-SIGNAL SOUND)

The tone of the turn-signal light operation sound can be changed on the function setting screen of the combination meter.

Modification method

1. Press the multi-information display switch (screen switching switch) several times to display the "Function setting screen" on the multi-information display.

2. Press the multi-information display switch (MENU switch) to switch to the top screen.

3. Press the multi-information display switch (screen switching switch) several times to display the "Turn signal sound."

note	The current tone will be displayed on the screen.

4. When the multi-information display switch (MENU switch) is press while "Turn signal sound" is displayed, the screen switches to the change screen.

5. The tone can be changed by pressing the multi-information display switch (MENU switch) while "SOUND 1" or "SOUND 2" is selected.