[Previous][Next]
INSPECTION
 
 
REMOTE CONTROLLED DOOR MIRROR OPERATION CHECK
Remove the door trim, and then connect the battery to the door mirror assembly connector to check that the door mirror operates.
 
VEHICLE WITH CAMERA
Battery connectionOperation direction
  • Connect terminal No. 13 to the negative battery terminal.
  • Connect terminal No. 4 to the positive battery terminal.
Up
  • Connect terminal No. 13 to the positive battery terminal.
  • Connect terminal No. 4 to the negative battery terminal.
Down
  • Connect terminal No. 13 to the negative battery terminal.
  • Connect terminal No. 12 to the positive battery terminal.
Right
  • Connect terminal No. 13 to the positive battery terminal.
  • Connect terminal No. 12 to the negative battery terminal.
Left
  • Connect terminal No. 14 to the positive battery terminal.
  • Connect terminal No. 5 to the negative battery terminal.
Retract
  • Connect terminal No. 14 to the negative battery terminal.
  • Connect terminal No. 5 to the positive battery terminal.
Extend
VEHICLE WITH CAMERA
Battery connectionOperation direction
  • Connect terminal No. 13 to the negative battery terminal.
  • Connect terminal No. 4 to the positive battery terminal.
Up
  • Connect terminal No. 13 to the positive battery terminal.
  • Connect terminal No. 4 to the negative battery terminal.
Down
  • Connect terminal No. 13 to the negative battery terminal.
  • Connect terminal No. 12 to the positive battery terminal.
Right
  • Connect terminal No. 13 to the positive battery terminal.
  • Connect terminal No. 12 to the negative battery terminal.
Left
  • Connect terminal No. 14 to the positive battery terminal.
  • Connect terminal No. 5 to the negative battery terminal.
Retract
  • Connect terminal No. 14 to the negative battery terminal.
  • Connect terminal No. 5 to the positive battery terminal.
Extend
 
VEHICLE WITHOUT CAMERA
Battery connectionOperation direction
  • Connect terminal No. 2 to the negative battery terminal.
  • Connect terminal No. 1 to the positive battery terminal.
Up
  • Connect terminal No. 2 to the positive battery terminal.
  • Connect terminal No. 1 to the negative battery terminal.
Down
  • Connect terminal No. 2 to the negative battery terminal.
  • Connect terminal No. 3 to the positive battery terminal.
Right
  • Connect terminal No. 2 to the positive battery terminal.
  • Connect terminal No. 3 to the negative battery terminal.
Left
  • Connect terminal No. 11 to the positive battery terminal.
  • Connect terminal No. 10 to the negative battery terminal.
Retract
  • Connect terminal No. 11 to the negative battery terminal.
  • Connect terminal No. 10 to the positive battery terminal.
Extend
VEHICLE WITHOUT CAMERA
Battery connectionOperation direction
  • Connect terminal No. 2 to the negative battery terminal.
  • Connect terminal No. 1 to the positive battery terminal.
Up
  • Connect terminal No. 2 to the positive battery terminal.
  • Connect terminal No. 1 to the negative battery terminal.
Down
  • Connect terminal No. 2 to the negative battery terminal.
  • Connect terminal No. 3 to the positive battery terminal.
Right
  • Connect terminal No. 2 to the positive battery terminal.
  • Connect terminal No. 3 to the negative battery terminal.
Left
  • Connect terminal No. 11 to the positive battery terminal.
  • Connect terminal No. 10 to the negative battery terminal.
Retract
  • Connect terminal No. 11 to the negative battery terminal.
  • Connect terminal No. 10 to the positive battery terminal.
Extend
 
 
 
REMOTE CONTROLLED MIRROR SWITCH CONTINUITY CHECK
 
Switch positionTester connectionSpecified condition
Left sideUp1 - 4, 1 - 8, 2 - 10Continuity
exists(2 ohms or less)
Down1 - 2, 4 - 8, 4 - 10
Right1 - 2, 1 - 4, 8 - 10
Left1 - 8, 2 - 4, 2 - 10
Right sideUp1 - 4, 1 - 7, 9 - 10
Down1 - 9, 4 - 7, 4 - 10
Right1 - 4, 1 - 9, 7 - 10
Left1 - 7, 4 - 9, 4 - 10
Retract and extend1 - 3
Switch positionTester connectionSpecified condition
Left sideUp1 - 4, 1 - 8, 2 - 10Continuity
exists(2 ohms or less)
Down1 - 2, 4 - 8, 4 - 10
Right1 - 2, 1 - 4, 8 - 10
Left1 - 8, 2 - 4, 2 - 10
Right sideUp1 - 4, 1 - 7, 9 - 10
Down1 - 9, 4 - 7, 4 - 10
Right1 - 4, 1 - 9, 7 - 10
Left1 - 7, 4 - 9, 4 - 10
Retract and extend1 - 3
 
 
 
HEATED DOOR MIRROR CHECK
cautionWhen relocating the car between locations with extremely different temperatures (warm and cold), leave the car in the location for a while to adapt to the temperature prior to checking it.
Check that the resistance value between the door mirror assembly connector terminal No. 1 and 9 <vehicles with camera>/No. 7 and 8 <vehicles without camera> is at the standard value.
Standard value: 7.2 ± 1.4 ohms at 25°C (77°F)
 
 
 
BLIND SPOT WARNING LIGHT CHECK
 
 
BLIND SPOT WARNING LIGHT CHECK
1.
cautionDo not apply battery voltage to door mirror assembly connector No. 3 terminal as the blind spot warning light is broken.
Apply 5V to the door mirror assembly connector terminal No. 3 <vehicles with camera>/No. 4 <vehicles without camera>, ground the terminal No. 11 <vehicles with camera>/No. 5 <vehicles without camera>, and then check that the illumination lights up.
2.
cautionDo not apply battery voltage to blind spot warning light connector No. 1 terminal as the blind spot warning light is broken.
Apply 5V to the blind spot warning light connector terminal No. 1, ground the terminal No. 2, and then check that the illumination lights up.
 
 
 
Checking the door mirror main wiring harness wires for continuity
Check the continuity between the door mirror assembly connector and the blind spot warning light connector.
 
<Vehicles with camera>
CircuitTester connectionSpecified condition
Power supplyDoor mirror assembly connector terminal No. 3 - blind spot warning light connector terminal No. 1Continuity
exists (2 ohms or less)
GroundDoor mirror assembly connector terminal No. 11 - blind spot warning light connector terminal No. 2
<Vehicles with camera>
CircuitTester connectionSpecified condition
Power supplyDoor mirror assembly connector terminal No. 3 - blind spot warning light connector terminal No. 1Continuity
exists (2 ohms or less)
GroundDoor mirror assembly connector terminal No. 11 - blind spot warning light connector terminal No. 2
 
<Vehicles without camera>
CircuitTester connectionSpecified condition
Power supplyDoor mirror assembly connector terminal No. 4 - blind spot warning light connector terminal No. 1Continuity
exists (2 ohms or less)
GroundDoor mirror assembly connector terminal No. 5 - blind spot warning light connector terminal No. 2
<Vehicles without camera>
CircuitTester connectionSpecified condition
Power supplyDoor mirror assembly connector terminal No. 4 - blind spot warning light connector terminal No. 1Continuity
exists (2 ohms or less)
GroundDoor mirror assembly connector terminal No. 5 - blind spot warning light connector terminal No. 2