[Previous] [Next]

TC-SST TEACH-IN


TEACH-IN ITEM


1. Scan tool item execution


To complete each Teach-In operation, multiple items must be executed using scan tool MB991958, and those items shall be executed in a designated order.

1-1. SCAN TOOL ITEM LIST
Item No.
 Scan tool Item Name
1
 Plausibility check
2
 Shift fork Teach-In
3
 Line pressure Test
4
 Stroke Teach-In
5
 Boost Teach-In
6
 Interlock Teach-In
7
 Clutch Ventilation
8
 Reset clutch gain
note
  • Item No. 3 and No. 6 are displayed on the scan tool, however, those are not used.
  • Item No.8 is not displayed when the Diag. Version of TC-SST-ECU is pre-0002. (Diag. Version can be checked by the Teach-In screen of scan tool.)

1-2. ITEM EXECUTION ORDER
Type
 Teach-In
 Item execution order
A
 Teach-In for Shift fork
 No.1 → No.7 → No.2
B
 Teach-In for Clutch
 No.7 → No.4 → No.5 → No.8
note Item No.8 is not displayed when the Diag. Version of TC-SST-ECU is pre-0002. (Diag. Version can be checked by the Teach-In screen of scan tool.)

2. Confirmation of Teach-In operation status


Using the data list simultaneously displayed with Teach-In, the execution status and results can be confirmed.
No.
 Data List Item Name
 Scan tool display
100
 Teach-In executing
 No/Pending/Yes
101
 Normal End
 No/Yes
102
 Abnormal End
 No/Yes
103
 Timeout error
 No/Yes
104
 Abort conditions error
 No/Yes
110
 Execute last Teach-In item
 The previously conducted scan tool item name is displayed
111
 Internal Error Data
 The monitoring unit No. is displayed in case of an error

TEACH-IN PROCEDURE


note
  • According to the transmission fluid state (fluid -filled state), Teach-In executed time is not equal.
  • Item No.8 is not displayed when the Diag. Version of TC-SST-ECU is pre-0002. (Diag. Version can be checked by the Teach-In screen of scan tool.)
Steps
 Contents
1
 With the scan tool connected and the vehicle set to the condition below, execute the Teach-In.

  • Engine: Idling
  • Shift lever position: P range
  • Brake pedal: Depressed
  • Parking brake: Pulled
  • Transmission fluid temperature: 40°C to 80°C (104°F to 176°F)
2
 Select "Special Function" of TC-SST.
3
 Select "Teach-In" of Special Function.
4
 According to "1-2 Item execution order", select the Item No. 1: Plausibility check to execute.
note Before execution, "No" is displayed in the Data list No. 100: Teach-In executing.
5
 After execution, check that "Yes" is displayed in the Data list No. 100: Teach-In executing.
note In a case other than the execution conditions, "Pending" is displayed in the Data list No. 100: Teach-In executing.
6
 After the Teach-In (Item No. 1: Plausibility check) completion, check that "No" is displayed in the Data list No. 100: Teach-In executing and execution results are displayed in the Data list No. 101 to No. 104.

  • No.101: Normal End: On normal end, "Yes" is displayed.
  • No.102: Abnormal End: On abnormal end, "Yes" is displayed.
  • No.103: Timeout error: On timeout error, "Yes" is displayed.
  • No.104: Abort conditions error: In a case other than the execution conditions, "Yes" is displayed.
7
 Change the item to No. 7: Clutch Ventilation, and execute steps from 4 to 6 in the same manner.
8
 Change the item to No. 2: Shift fork Teach-In, and execute steps from 4 to 6 in the same manner.
9
 Turn the ignition switch to the LOCK (OFF) position.
10
 Change the item to No. 7: Clutch Ventilation, and execute steps from 4 to 6 in the same manner.
11
 Change the item to No. 4: Stroke Teach-In, and execute steps from 4 to 6 in the same manner.
12
caution Be careful with the following item when performing Item No.5: Boost Teach-In.

  • The engine speed could be high (4,000 r/min) when the Boost Teach-In is in progress. (Depending on the transaxle state, the engine speed may not be high.)
Change the item to No. 5: Boost Teach-In, and execute steps from 4 to 6 in the same manner.
13
 Change the item to No. 8: Reset clutch gain, and execute steps from 4 to 6 in the same manner.
14
 Turn the ignition switch to the LOCK (OFF) position.