![[Previous]](../../../buttons/fprev.png)
![[Next]](../../../buttons/fnext.png)
DTC P0013: Exhaust
Engine Oil Control Valve Circuit
CIRCUIT OPERATION
- The exhaust engine oil control valve power is supplied
from the MFI relay (terminal No. 2).
- The ECM controls ground exhaust engine oil control valve by turning the power transistor
in the ECM "ON" and "OFF".
TECHNICAL DESCRIPTION
- The exhaust engine oil control valve changes the phase
angle to operate the MIVEC system in the advance or the retard side in accordance with signals
from the ECM.
DESCRIPTIONS OF MONITOR METHODS
Exhaust engine oil control valve circuit current is
out of the specified range.
MONITOR EXECUTION
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored in memory
for the item monitored below)
Sensor (The sensor below is determined to be normal)
- Camshaft position sensor
- Crankshaft position sensor
- Engine coolant temperature sensor
- Throttle position sensor
- Engine oil control valve
DTC SET CONDITIONS
Logic Flow Chart
Check Conditions
- Ignition switch is "ON" position.
- Battery positive voltage is between 10 and 16.5 volts.
- ON duty cycle of the exhaust engine oil control valve circuit is higher than 20
percent.
Judgement Criterion
- The ECM terminal current of exhaust engine oil control valve circuit is less than
0.1 ampere for 2 seconds.
Check Conditions
- Ignition switch is "ON" position.
- Battery positive voltage is between 10 and 16.5 volts.
Judgement Criterion
- The ECM terminal current of exhaust engine oil control valve circuit is higher than
2.9 amperes for 0.1 second.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern
23 
.
TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
- Exhaust engine oil control valve failed.
- Open or shorted exhaust engine oil control valve circuit, or harness damage, or
connector damage.
- ECM failed.
|
|
Required Special Tools:
- MB991958: Scan Tool (M.U.T.-III Sub Assembly)
- MB991824: V.C.I.
- MB991827: USB Cable
- MB991911: Main Harness B
- MB992110:Power Plant ECU CHeck Harness
|
|
|
STEP 1. Check harness connector B-19 at the exhaust engine
oil control valve for damage.
|
|
|
Q.
Is the harness connector in good condition?
|
|
|
 Go to Step 2.
|
|
|
|
|
|
 Repair or replace it. Refer to GROUP 00E, Harness Connector Inspection .
Then go to Step 10.
|
|
|
|
|
|
STEP 2. Check the exhaust engine oil control valve.
|
|
|
(1)Disconnect the exhaust engine oil control valve connector B-19.
|
|
(2)Measure the resistance between exhaust engine oil control valve side connector terminal
No. 1 and No. 2.
Standard value: 6.9 - 7.9 Ω [at 20°C (68°F)]
Q.
Is the measured resistance between 6.9 and 7.9 Ω [at 20°C
(68°F)]?
Go to Step 3.
Replace the exhaust engine oil control valve. Then go to Step 10.
|
|
|
STEP 3. Measure the power supply voltage at exhaust engine oil control
valve harness side connector B-19.
|
|
|
(1)Disconnect the connector B-19 and measure at the harness side.
|
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Measure the voltage between terminal No. 2 and ground.
- Voltage should be battery positive voltage.
(4)Turn the ignition switch to the "LOCK" (OFF) position.
Q.
Is battery positive voltage (approximately 12 volts) present?
Go to Step 5.
Go to Step 4.
|
|
|
STEP 4. Check harness connector A-30X at MFI relay for damage.
|
|
|
Q.
Is the harness connector in good condition?
|
|
|
Check harness connector A-10 at intermediate connector for damage, and repair
or replace as required. Refer to GROUP 00E, Harness Connector Inspection .
If intermediate connector is in good condition, repair harness wire between MFI relay connector
A-30X (terminal No. 2) and exhaust engine oil control valve connector B-19 (terminal No. 2) because
of open circuit or short circuit to ground. Then go to Step 10.
|
|
|
|
|
|
Repair or replace it. Refer to GROUP 00E, Harness Connector Inspection .
Then go to Step 10.
|
|
|
|
|
|
STEP 5. Check harness connector B-108 at ECM for damage.
|
|
|
Q.
Is the harness connector in good condition?
|
|
|
Go to Step 6.
|
|
|
|
|
|
Repair or replace it. Refer to GROUP 00E, Harness Connector Inspection .
Then go to Step 10.
|
|
|
|
|
|
STEP 6. Measure the power supply voltage at ECM connector B-108 by
using power plant ECU check harness special tool MB992110.
|
|
(1)Disconnect all ECM connectors. Connect the power plant ECU check harness special
tool MB992110 between the separated connectors.
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Measure the voltage between terminal No. 17 and ground.
- Voltage should be battery positive voltage.
(4)Turn the ignition switch to the "LOCK" (OFF) position.
Q.
Is battery positive voltage (approximately 12 volts) present?
Go to Step 7.
Repair harness wire between exhaust engine oil control valve connector B-19 (terminal
No. 1) and ECM connector B-108 (terminal No. 17) because of open circuit or short circuit to
ground. Then go to Step 10.
|
|
|
STEP 7. Check for harness damage between MFI relay connector A-30X
(terminal No. 2) and exhaust engine oil control valve connector B-19 (terminal No. 2).
|
|
|
| note |
Check harness after checking intermediate connector A-10. If intermediate connector is
damaged, repair or replace it. Refer to GROUP 00E, Harness Connector Inspection . Then
go to Step 10.
|
|
|
|
Q.
Is the harness wire in good condition?
|
|
|
Go to Step 8.
|
|
|
|
|
|
Repair it. Then go to Step 10.
|
|
|
|
|
|
STEP 8. Check for harness damage between exhaust engine oil control
valve connector B-19 (terminal No. 1) and ECM connector B-108 (terminal No. 17).
|
|
|
Q.
Is the harness wire in good condition?
|
|
|
Go to Step 9.
|
|
|
|
|
|
Repair it. Then go to Step 10.
|
|
|
|
|
|
STEP 9. Check the trouble symptoms.
|
|
|
(1)Carry out test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II
Drive Cycle - Pattern 23 .
|
|
|
(2)Check the diagnostic trouble code (DTC).
|
|
|
Replace the ECM. When the ECM is replaced, register the ID code. Refer to GROUP
42B, Diagnosis - ID Code Registration Judgment Table <Vehicles with KOS> or
GROUP 42C, Diagnosis - ID Codes Registration Judgment Table <Vehicles with WCM> .
Then go to Step 10.
|
|
|
|
|
|
It can be assumed that this malfunction is intermittent. Refer to GROUP 00, How
to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions .
|
|
|
|
|
|
STEP 10. Test the OBD-II drive cycle.
|
|
|
(1)Carry out test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II
Drive Cycle - Pattern 23 .
|
|
|
(2)Check the diagnostic trouble code (DTC).
|
|
|
Retry the troubleshooting.
|
|
|
|
|
|
The inspection is complete.
|
|
|
|
)
)
)
)
)
)
)
)
)
)