[Previous][Next]
DTC C1560: Vehicle speed data (CAN)
 
 
caution
  • If there is any problem in the CAN bus lines, an incorrect diagnostic trouble code (DTC) may be set. Prior to this diagnosis, diagnose the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ).
  • Whenever ECU is replaced, ensure that the CAN bus lines are normal.
 
 
OPERATION
EPS-ECU receives vehicle speed signal from the engine control module (ECM).
 
 
DIAGNOSTIC TROUBLE CODE SET CONDITION
EPS-ECU receives the vehicle speed data from the ECM via CAN bus lines. If the EPS-ECU cannot receive the vehicle speed data from the ECM, DTC C1560 will be set.
 
 
COMMENT ON TROUBLE SYMPTOM
Current trouble
  • The wiring harness or connector in the CAN bus lines between the EPS-ECU and ECM, the power supply system of the ECM, or the EPS-ECU itself may be defective.
Past trouble
  • If DTC C1560 is set as a historic trouble, carry out the diagnosis with particular emphasis on the wiring harness and connector in the CAN bus lines between the EPS-ECU and ECM as well as on the power supply system of the ECM. For diagnosis procedures, refer to "How to treat past trouble" (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points, How to Treat Past Trouble ).
    noteIn case of a historic trouble, the scan tool (M.U.T.-III) CAN bus diagnosis cannot find the problem even when there is an abnormality in the CAN bus. In this case, be sure to diagnose the CAN bus lines in the same manner as for "How to Cope with Intermittent Malfunction" (refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points, How to Cope with Intermittent Malfunctions ). You can narrow down the possible cause of the trouble by referring to the diagnostic trouble code, which is set regarding the CAN communication-linked ECUs (refer to GROUP 54C - Explanation About the Using SCAN Tool (M.U.T.-III), diagnose the CAN bus lines. ).
 
 
PROBABLE CAUSES
  • Malfunction of CAN bus line
  • Defective harness wire(s) or connector(s)
  • Malfunction of the ECM.
  • Malfunction of the EPS-ECU
 
 
DIAGNOSIS
Required Special Tools:
  • MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
  • MB992745: V.C.I.-Lite main harness A
  • MB992747: V.C.I.-Lite USB cable short
  • MB992748: V.C.I.-Lite USB cable long
  • MB991958: Scan Tool (M.U.T.-III Sub Assembly)
    • MB991824: Vehicles Communication Interface (V.C.I.)
    • MB991827: M.U.T.-III USB Cable
    • MB991910: M.U.T.-III Main Harness A (Vehicles with CAN communication system)
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus lines.
Use the scan tool (M.U.T.-III) to diagnose the CAN bus lines.
Is the check result normal?
Go to Step 3.
Repair the CAN bus lines (Refer to GROUP 54C - Troubleshooting ). After repairing the CAN bus lines, go to Step 2.
 
STEP 2. Diagnostic trouble code recheck after repairing CAN bus lines.
(1) Erase the diagnostic trouble code.
(2) Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
(3) Check if the diagnostic trouble code is set.
Is DTC C1560 set?
Go to Step 3.
This diagnosis is complete.
 
STEP 3. Use scan tool (M.U.T.-III) to confirm a diagnostic trouble code of other systems.
Check that the MFI system set a diagnostic trouble code.
Is the diagnostic trouble code set?
Perform the troubleshooting for the MFI system (Refer to GROUP 13A - Troubleshooting ).
Go to Step 4.
 
STEP 4. Check whether the diagnostic trouble code is set again.
(1) Erase the diagnostic trouble code.
(2) Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
(3) Check if the diagnostic trouble code is set.
Is DTC C1560 set?
Replace the EPS-ECU (Refer to ), and then go to Step 5.
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points, How to Cope with Intermittent Malfunctions ).
 
STEP 5. Check whether the diagnostic trouble code is set again.
(1) Erase the diagnostic trouble code.
(2) Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
(3) Check if the diagnostic trouble code is set.
Is DTC C1560 set?
Return to Step 1.
The diagnosis is complete.