[Previous][Next]
DTC U0100: Engine CAN timeout
 
 
caution
  • If DTC U0100 is set, be sure to diagnose the CAN bus line.
  • Before replacing ECU, ensure that the communication circuit is normal.
 
 
DTC SET CONDITION
When the signal from the engine control module cannot be received, KOS&OSS-ECU sets DTC U0100.
 
 
TROUBLESHOOTING HINTS
  • Malfunction of the CAN bus line
  • Engine control module malfunction
  • Malfunction of KOS&OSS-ECU
 
 
DIAGNOSIS
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.
(1)
cautionTo prevent damage to scan tool (M.U.T.-III), always turn the power supply mode of the engine switch to the "OFF" position before connecting or disconnecting scan tool (M.U.T.-III).
Connect scan tool (M.U.T.-III) [Refer to "How to connect scan tool (M.U.T.-III) "].
(2) Turn the power supply mode of the engine switch to "ON".
(3) Diagnose the CAN bus line.
(4) Turn the power supply mode of the engine switch to "OFF".
Is the CAN bus line found to be normal?
Go to Step 2.
Repair the CAN bus line (Refer to GROUP 54C, Diagnosis ).
 
STEP 2. Using scan tool (M.U.T.-III), read the other system diagnostic trouble code.
Check again if the DTC is set in the engine control module.
(1)
cautionTo prevent damage to scan tool (M.U.T.-III), always turn the power supply mode of the engine switch to the "OFF" position before connecting or disconnecting scan tool (M.U.T.-III).
Connect scan tool (M.U.T.-III) [Refer to "How to connect scan tool (M.U.T.-III) "].
(2) Erase the DTC.
(3) Turn the power supply mode of the engine switch to "ON".
(4) Check if DTC is set.
(5) Turn the power supply mode of the engine switch to "OFF".
Is the DTC set?
Perform troubleshooting for the engine control module (Refer to GROUP 13A, Troubleshooting ). On completion, go to Step 3.
Go to Step 3.
 
STEP 3. Using scan tool (M.U.T.-III), read the other system diagnostic trouble code.
Check if DTC U0100 is set in the combination meter.
(1)
cautionTo prevent damage to scan tool (M.U.T.-III), always turn the power supply mode of the engine switch to the "OFF" position before connecting or disconnecting scan tool (M.U.T.-III).
Connect scan tool (M.U.T.-III) [Refer to "How to connect scan tool (M.U.T.-III) "].
(2) Erase the DTC.
(3) Turn the power supply mode of the engine switch to "ON".
(4) Check if DTC is set.
(5) Turn the power supply mode of the engine switch to "OFF".
Is the DTC set?
Go to Step 4.
Go to Step 5.
 
STEP 4. Recheck for diagnostic trouble code.
Check again if the DTC is set in the KOS&OSS-ECU.
(1) Erase the DTC.
(2) Turn the power supply mode of the engine switch from "OFF" to "ON".
(3) Check if DTC is set.
(4) Turn the power supply mode of the engine switch from "ON" to "OFF".
Is the DTC set?
Replace the engine control module.
A poor connection, open circuit or other intermittent malfunction is present in the CAN bus lines between the engine control module and the KOS&OSS-ECU (Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
 
STEP 5. Recheck for diagnostic trouble code.
Check again if the DTC is set in the KOS&OSS-ECU.
(1) Erase the DTC.
(2) Turn the power supply mode of the engine switch from "OFF" to "ON".
(3) Check if DTC is set.
(4) Turn the power supply mode of the engine switch from "ON" to "OFF".
Is the DTC set?
Replace the KOS&OSS-ECU and register the ID codes (Refer to ).
A poor connection, open circuit or other intermittent malfunction is present in the CAN bus lines between the engine control module and the KOS&OSS-ECU (Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).