[Previous][Next]
DTC U0155: Meter CAN timeout
 
 
caution
  • If diagnostic trouble code No. U0155 is set, be sure to diagnose the CAN bus line.
  • When replacing the ECU, always check that the communication circuit is normal.
 
 
TROUBLE JUDGMENT
If no signal from the combination meter can be received, KOS&OSS-ECU sets DTC U0155.
 
 
TROUBLESHOOTING HINTS
  • Malfunction of CAN bus line
  • Combination meter malfunction
  • Malfunction of KOS&OSS-ECU
 
 
DIAGNOSIS
STEP 1. Using scan tool (M.U.T.-III), diagnose the CAN bus line.
(1)
cautionTo prevent damage to scan tool (M.U.T.-III), always turn the power supply mode of the engine switch to the "OFF" position before connecting or disconnecting scan tool (M.U.T.-III).
Connect scan tool (M.U.T.-III) [Refer to "How to connect the scan tool (M.U.T.-III) "].
(2) Turn the power supply mode of the engine switch to "ON".
(3) Diagnose the CAN bus line.
(4) Turn the power supply mode of the engine switch to "OFF".
Is the CAN bus line found to be normal?
Go to Step 2.
Repair the CAN bus line (Refer to GROUP 54C, Diagnosis ).
 
STEP 2. Using scan tool (M.U.T.-III), read the combination meter diagnostic trouble code.
Check if DTC is set in the combination meter.
(1)
cautionTo prevent damage to scan tool (M.U.T.-III)), always turn the power supply mode of the engine switch to the "OFF" position before connecting or disconnecting scan tool (M.U.T.-III).
Connect scan tool (M.U.T.-III) [Refer to "How to connect the scan tool (M.U.T.-III) "].
(2) Turn the power supply mode of the engine switch to "ON".
(3) Diagnose the DTC.
(4) Turn the power supply mode of the engine switch to "OFF".
Is the DTC set?
Troubleshoot the combination meter (Refer to GROUP 54A, Diagnosis ).
Go to Step 3.
 
STEP 3. Using scan tool (M.U.T.-III), read the other system diagnostic trouble code.
Check if DTC U0155 is set in the engine control module.
(1)
cautionTo prevent damage to scan tool (M.U.T.-III), always turn the power supply mode of the engine switch to the "OFF" position before connecting or disconnecting scan tool (M.U.T.-III).
Connect scan tool (M.U.T.-III) [Refer to "How to connect scan tool (M.U.T.-III) "].
(2) Erase the DTC.
(3) Turn the power supply mode of the engine switch to "ON".
(4) Check if DTC is set.
(5) Turn the power supply mode of the engine switch to "OFF".
Is the DTC set?
Go to Step 4.
Go to Step 5.
 
STEP 4. Recheck for diagnostic trouble code.
Check again if the DTC is set in the KOS&OSS-ECU.
(1) Erase the DTC.
(2) Turn the power supply mode of the engine switch from "OFF" to "ON".
(3) Check if DTC is set.
(4) Turn the power supply mode of the engine switch from "ON" to "OFF".
Is the DTC set?
Replace the combination meter.
A poor connection, open circuit or other intermittent malfunction is present in the CAN bus lines between the combination meter and the KOS&OSS-ECU (Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).
 
STEP 5. Recheck for diagnostic trouble code.
Check again if the DTC is set in the KOS&OSS-ECU.
(1) Erase the DTC.
(2) Turn the power supply mode of the engine switch from "OFF" to "ON".
(3) Check if DTC is set.
(4) Turn the power supply mode of the engine switch from "ON" to "OFF".
Is the DTC set?
Replace KOS&OSS-ECU and register the ID codes (Refer to ).
A poor connection, open circuit or other intermittent malfunction is present in the CAN bus lines between the combination meter and the KOS&OSS-ECU (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).