[Previous][Next]
DTC P0133: Linear Air-Fuel Ratio Sensor Circuit Slow Response
 
 
 
 
TECHNICAL DESCRIPTION
  • The ECM effects air/fuel ratio feedback control in accordance with the signals from the linear air-fuel ratio sensor.
  • If the linear air-fuel ratio sensor has deteriorated, corrections will be made by the heated oxygen sensor (rear).
 
 
DESCRIPTIONS OF MONITOR METHODS
  • If the response speed of the linear air-fuel ratio sensor to the change in the air-fuel ratio is too slow, the DTC is set as the linear air-fuel ratio sensor deterioration.
 
 
MONITOR EXECUTION
  • Continuous
 
 
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
  • Linear air-fuel ratio sensor heater monitor
  • Misfire monitor
  • Fuel system monitor
Sensor (The sensor below is determined to be normal)
  • Mass airflow sensor
  • Engine coolant temperature sensor
  • Intake air temperature sensor
  • Barometric pressure sensor
  • Throttle position sensor
  • Accelerator pedal position sensor
 
 
DTC SET CONDITIONS
Logic Flow Chart
 
 
Check Conditions
  • Engine speed is between 2,000 and 4,000 r/min <M/T> or 1,250 and 3,000 r/min <CVT>.
  • Volumetric efficiency is between 22 and 65 percent.
  • Engine coolant temperature is more than 60°C (140°F).
  • Under the closed loop air/fuel control.
  • The accelerator pedal is depressed.
  • Short-term fuel trim is between -25 and +25 percent.
  • More than 3 seconds have passed after the above mentioned conditions have been met.
  • During the drive cycle, the ECM performs monitoring with the accumulated total time of 10 seconds, 5 times.
Judgment Criteria
  • The average frequency is less than 8 times.
  • The frequency is less than 16 times.
 
 
FAIL-SAFE AND BACKUP FUNCTION
  • None
 
 
OBD-II DRIVE CYCLE PATTERN
  • Refer to Diagnosis Function - OBD-II Drive Cycle - Pattern 1 .
 
 
TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
  • Linear air-fuel ratio sensor failed.
  • Connector damage.

 
 
DIAGNOSIS
Required Special Tools:
  • MB992744: Vehicle communication interface-Lite (V.C.I.-Lite)
  • MB992745: V.C.I.-Lite main harness A
  • MB992747: V.C.I.-Lite USB cable short
  • MB992748: V.C.I.-Lite USB cable long
  • MB991958: Scan Tool (M.U.T.-III Sub Assembly)
    • MB991824: Vehicles Communication Interface (V.C.I.)
    • MB991827: M.U.T.-III USB Cable
    • MB991910: M.U.T.-III Main Harness A (Vehicles with CAN communication system)
STEP 1. Check harness connector at linear air-fuel ratio sensor and harness connector at ECM for damage.
Is the harness connector in good condition?
Go to Step 2.
Repair or replace it. Refer to GROUP 00E, Harness Connector Inspection . Then go to Step 3.
 
STEP 2. Test the OBD-II drive cycle.
cautionTo prevent damage to scan tool (M.U.T.-III), always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool (M.U.T.-III).
(1) Connect scan tool (M.U.T.-III). Refer to HOW TO CONNECT THE SCAN TOOL (M.U.T.-III) .
(2) Turn the ignition switch to the "ON" position and delete the DTC.
(3) Carry out the test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 1 .
(4) Check the diagnostic trouble code (DTC).
Is DTC P0133 set?
Replace the linear air-fuel ratio sensor. Then go to Step 3.
It can be assumed that this malfunction is intermittent. Refer to GROUP 00, How to Use Troubleshooting/ Inspection Service Points - How to Cope with Intermittent Malfunctions .
 
STEP 3. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 1 .
(2) Check the diagnostic trouble code (DTC).
Is DTC P0133 set?
Retry the troubleshooting.
The inspection is complete.